EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Application of Kolmogorov–Sinai’s Metric Entropy for the Analysis of Mechanical Properties in the Bending Test of Epoxy–Rubber–Glass Composites

Norbert Abramczyk iD, Grzegorz Hajdukiewicz iD, Adam Charchalis, Daria Żuk iD

Materials · 18.10.2024 · 17 (20) · 5079

DOI: 10.3390/ma17205079 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.10.2024. Verfasst von Norbert Abramczyk und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Marine Engineering, Gdynia Maritime University, 81-225 Gdynia, Poland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The article presents an analysis of the results obtained during the three-point bending test for seven variants of epoxy rubber–glass composites manufactured according to innovative technology. Different contents of rubber recyclate (3, 5, and 7%) and different methods of distribution of the recyclate in the composite structure (1, 2, and 3 layers with a constant share of 5% of the recyclate) were used in the tested materials. To determine the stress values at which critical failures of the tested materials are initiated in the bending test, an analysis was carried out using the Kolmogorov–Sinai (EK-S) metric entropy calculations. The analysis results showed that for each of the above-mentioned variants of the tested epoxy–glass composites, the onset of critical changes occurring in the material structure occurs below the recorded values of the flexural strength Rmg. The decrease in the RmgK-S value in relation to Rmg is different for different material variants and depends mainly on the % content of rubber recyclate and the amount and method of decomposition of rubber recyclate in the layers of the analyzed materials. The research showed that the introduction of rubber recyclate into the composition of composites has a positive effect on their strength properties. This process allows for the efficient use of hard to degrade waste and opens up the possibility of using the newly developed materials in many industrial sectors.

Schlagwörter

Stichwörter der Autor:innen

Kolmogorov–Sinai metric entropyepoxy–rubber–glass compositesrubber recyclatethree-point bending test

Autor:innen und Institutionen

  • Faculty of Marine Engineering, Gdynia Maritime University, 81-225 Gdynia, Poland.

ORCID-Profile: Norbert Abramczyk, Grzegorz Hajdukiewicz, Daria Żuk

Zitieren

APA

Abramczyk, N., Hajdukiewicz, G., Charchalis, A., & Żuk, D. (2024). Application of Kolmogorov–Sinai’s Metric Entropy for the Analysis of Mechanical Properties in the Bending Test of Epoxy–Rubber–Glass Composites. Materials, 17(20), 5079. https://doi.org/10.3390/ma17205079

Vancouver

Abramczyk N, Hajdukiewicz G, Charchalis A, Żuk D. Application of Kolmogorov–Sinai’s Metric Entropy for the Analysis of Mechanical Properties in the Bending Test of Epoxy–Rubber–Glass Composites. Materials. 2024;17(20):5079. doi:10.3390/ma17205079

BibTeX
@article{Abramczyk2024,
  author = {Abramczyk, Norbert and Hajdukiewicz, Grzegorz and Charchalis, Adam and Żuk, Daria},
  title = {Application of Kolmogorov–Sinai’s Metric Entropy for the Analysis of Mechanical Properties in the Bending Test of Epoxy–Rubber–Glass Composites},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {20},
  pages = {5079},
  doi = {10.3390/ma17205079}
}
Kostenlos starten →