EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of an Alternative Manufacturing Technology for Niobium Components

Anna Kawalek iD, Kirill Ozhmegov iD, Dariusz Garbiec iD, Henryk Dyja, Alexandr Arbuz

Materials · 24.06.2024 · 17 (13) · 3093

DOI: 10.3390/ma17133093 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.06.2024. Verfasst von Anna Kawalek und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Production Engineering and Materials Technology, Częstochowa University of Technology, ul. J.H. Dąbrowskiego 69, 42-201 Częstochowa, Polan…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Due to their physical and mechanical properties, niobium products are used in the nuclear power industry, chemical industry, electronics, medicine and in the defence industry. Traditional manufacturing technology for these products is characterized by long production cycles and significant material losses during their surface machining. This paper presents the results of a study on the fabrication of niobium products by Spark Plasma Sintering (SPS). Structural and mechanical tests were conducted on the products obtained, as well as a comparative analysis with the properties of products obtained using traditional technology. Based on the analysis of the test results obtained, recommendations were made for the sintering of Nb powders. It was found that the optimum temperature for sintering the powder is 2000 °C as the density of the material obtained is close to the theoretical density. The microstructure obtained is comparable to samples obtained by the traditional method after recrystallization annealing. Samples obtained according to the new technology are characterized by higher mechanical properties Rp0.2 and Rm and the highest hardness.

Schlagwörter

Stichwörter der Autor:innen

EBSDNb rodsSPS methodsmetallographypowder metallurgyrheological and strength propertiessintering parameters

Autor:innen und Institutionen

  • Faculty of Production Engineering and Materials Technology, Częstochowa University of Technology, ul. J.H. Dąbrowskiego 69, 42-201 Częstochowa, Poland.
  • Łukasiewicz Research Network, Poznań Institute of Technology, 6 Ewarysta Estkowskiego St., 61-755 Poznan, Poland.
  • Research Facility, AEO Nazarbayev University, 53 Kabanbay Batyr Ave, Nur-Sultan 010000, Kazakhstan.

ORCID-Profile: Anna Kawalek, Kirill Ozhmegov, Dariusz Garbiec

Zitieren

APA

Kawalek, A., Ozhmegov, K., Garbiec, D., Dyja, H., & Arbuz, A. (2024). Development of an Alternative Manufacturing Technology for Niobium Components. Materials, 17(13), 3093. https://doi.org/10.3390/ma17133093

Vancouver

Kawalek A, Ozhmegov K, Garbiec D, Dyja H, Arbuz A. Development of an Alternative Manufacturing Technology for Niobium Components. Materials. 2024;17(13):3093. doi:10.3390/ma17133093

BibTeX
@article{Kawalek2024,
  author = {Kawalek, Anna and Ozhmegov, Kirill and Garbiec, Dariusz and Dyja, Henryk and Arbuz, Alexandr},
  title = {Development of an Alternative Manufacturing Technology for Niobium Components},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {13},
  pages = {3093},
  doi = {10.3390/ma17133093}
}
Kostenlos starten →