EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Combining Metal Additive Manufacturing and Casting Technology: High Performance Cooling Channels for Electric Powertrain Components

Dirk Lehmhus, Gefei Li, Martin Czekalla, Leonardo Fernandes Gomes, Christoph Pille, Hermann Pleteit, Adrian Struss, Keno Toussaint, Andre Irretier, Münip Dalgic

Advanced Engineering Materials · 2025-08 · 27 (16)

DOI: 10.1002/adem.202500445 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Engineering Materials, online erschienen am 14.05.2025. Verfasst von Dirk Lehmhus und 9 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Electric powertrain components require fluid‐based thermal management. Al hollow sections integrate in high‐pressure die casting (HPDC) promise attractive performance, but require stabilizing fillers affording costly or technically risky removal. Additive manufacturing can facilitate eliminating the filler while further increasing performance via superior material strength, plus geometrical flexibility allowing for internal structuring to enhance heat transfer. Realizing these advantages affords solutions for predicting stability of arbitrary layouts under HPDC conditions. This study compares and validates three approaches employing MAGMASOFT casting simulation individually, and in combination with finite element (FE) simulation. As basis, temperature‐dependent mechanical properties for AlSi10Mg alloy processed via laser powder bed fusion are determined between room temperature and 450 °C. Yield strength for the stress relieved material state ranges from 119.63 MPa at RT to 21.90 MPa at 450 °C. Validation of simulation methodologies is done using a test die capable of accommodating tubes of 12 mm outer diameter, with casting experiments performed using a Bühler SC/N 66 HPDC machine. Approaches based on an approximative formula fell short of those combing casting and FE simulation regarding stability limits by a margin of up to 42%. Best match with experimental data is observed for the combined approach.

Zitieren

APA

Lehmhus, D., Li, G., Czekalla, M., Gomes, L. F., Pille, C., Pleteit, H., Struss, A., Toussaint, K., Irretier, A., & Dalgic, M. (2025). Combining Metal Additive Manufacturing and Casting Technology: High Performance Cooling Channels for Electric Powertrain Components. Advanced Engineering Materials, 27(16). https://doi.org/10.1002/adem.202500445

Vancouver

Lehmhus D, Li G, Czekalla M, Gomes LF, Pille C, Pleteit H, et al. Combining Metal Additive Manufacturing and Casting Technology: High Performance Cooling Channels for Electric Powertrain Components. Advanced Engineering Materials. 2025;27(16). doi:10.1002/adem.202500445

BibTeX
@article{Lehmhus2025,
  author = {Lehmhus, Dirk and Li, Gefei and Czekalla, Martin and Gomes, Leonardo Fernandes and Pille, Christoph and Pleteit, Hermann and Struss, Adrian and Toussaint, Keno and Irretier, Andre and Dalgic, Münip},
  title = {Combining Metal Additive Manufacturing and Casting Technology: High Performance Cooling Channels for Electric Powertrain Components},
  journal = {Advanced Engineering Materials},
  year = {2025},
  volume = {27},
  number = {16},
  doi = {10.1002/adem.202500445}
}
Kostenlos starten →