EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimising Mg-Ca/PLA Composite Filaments for Additive Manufacturing: An Analysis of Particle Content, Size, and Morphology

Hyeonseok Kim iD, Tom McKenna iD, Eoin O'Cearbhaill iD, Mert Celikin iD

Materials · 18.06.2024 · 17 (12) · 2983

DOI: 10.3390/ma17122983 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.06.2024. Verfasst von Hyeonseok Kim und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Materials Engineering, University College Dublin, D04 C1P1 Dublin, Ireland. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Foundation Ireland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Low-temperature additive manufacturing of magnesium (Mg) alloy implants is considered a promising technique for biomedical applications due to Mg’s inherent biocompatibility and 3D printing’s capability for patient-specific design. This study explores the influence of powder volume content, size, and morphology on the mechanical properties and viscosity of polylactic acid (PLA) matrix composite filaments containing in-house-produced magnesium–calcium (Mg-Ca) particles, with a focus on their application towards low-temperature additive manufacturing. We investigated the effects of varying the Mg-Ca particle content in a PLA matrix, revealing a direct correlation between volume content and bending strength. Particle size analysis demonstrated that smaller particles (D50: 57 μm) achieved a bending strength of 63.7 MPa, whereas larger particles (D50: 105 μm) exhibited 49.6 MPa at 20 vol.%. Morphologically, the filament containing spherical particles at 20 vol.% showed a bending strength that was 11.5 MPa higher than that of the filament with irregular particles. These findings highlight the critical role of particle content, size, and shape in determining the mechanical and rheological properties of Mg-Ca/PLA composite filaments for use in material extrusion additive manufacturing.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingbiomaterialsfilamentmagnesium alloymaterial extrusionparticle contentparticle morphologyparticle sizeviscosity

Autor:innen und Institutionen

  • School of Mechanical and Materials Engineering, University College Dublin, D04 C1P1 Dublin, Ireland.

ORCID-Profile: Hyeonseok Kim, Tom McKenna, Eoin O'Cearbhaill, Mert Celikin

Förderung

  • Science Foundation Ireland

Zitieren

APA

Kim, H., McKenna, T., O'Cearbhaill, E., & Celikin, M. (2024). Optimising Mg-Ca/PLA Composite Filaments for Additive Manufacturing: An Analysis of Particle Content, Size, and Morphology. Materials, 17(12), 2983. https://doi.org/10.3390/ma17122983

Vancouver

Kim H, McKenna T, O'Cearbhaill E, Celikin M. Optimising Mg-Ca/PLA Composite Filaments for Additive Manufacturing: An Analysis of Particle Content, Size, and Morphology. Materials. 2024;17(12):2983. doi:10.3390/ma17122983

BibTeX
@article{Kim2024,
  author = {Kim, Hyeonseok and McKenna, Tom and O'Cearbhaill, Eoin and Celikin, Mert},
  title = {Optimising Mg-Ca/PLA Composite Filaments for Additive Manufacturing: An Analysis of Particle Content, Size, and Morphology},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {12},
  pages = {2983},
  doi = {10.3390/ma17122983}
}
Kostenlos starten →