EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Jingbin Liu, Jingyi Hu, Mengyu Li, Guiliang Liu, Yuying Wu iD, Tong Gao iD, Shushuai Liu, Xiangfa Liu

Materials · 26.04.2024 · 17 (9) · 2022

DOI: 10.3390/ma17092022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.04.2024. Verfasst von Jingbin Liu und 7 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, 17923 Jingshi Road, Jin…. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Key Research and Development Program of Shandong Province, the Natural Science Foundation of Shandong Province, Natural Science Foundation of Shandong Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Here, 0.3 wt.%Zr was introduced in an Al-4 wt.%Cu-0.5 wt.%Mn-0.1 wt.%Fe alloy to investigate its influence on the microstructure and mechanical properties of the alloy. The microstructures of both as-cast and T6-treated Al–Cu–Mn–Fe (ACMF) and Al–Cu–Mn–Fe–Zr (ACMFZ) alloys were analyzed. The intermetallic compounds formed through the casting procedure include Al2Cu and Al7Cu2Fe, and the Al2Cu phase dissolves into the matrix and re-precipitates as θ′ phase during the T6 process. The introduction of Zr results in the precipitation of L12-Al3Zr nanometric precipitates after T6, while the θ′ precipitates in ACMFZ alloy are much finer than those in ACMF alloy. The L12-Al3Zr precipitates were found coherently located with θ′, which was assumed beneficial for stabilizing the θ′ precipitates during the high-temperature tensile process. The tensile properties of ACMF and ACMFZ alloys at room temperature and elevated temperatures (200, 300, and 400 °C) were tested. Especially, the yield strength of ACMFZ alloys can reach 128 MPa and 65 MPa at 300 °C and 400 °C, respectively, which are 31% and 33% higher than those of ACMF alloys. The strengthening mechanisms of grain size, L12-Al3Zr, and θ′ precipitates on the tensile properties were discussed. This work may be referred to for designing Al–Cu alloys for application in high-temperature fields.

Schlagwörter

Stichwörter der Autor:innen

Al–Cu–Mn–Fe alloyhigh-temperature strengthmicroalloyingmicrostructure

Autor:innen und Institutionen

  • Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, 17923 Jingshi Road, Jinan 250061, China.

ORCID-Profile: Yuying Wu, Tong Gao

Förderung

  • the Key Research and Development Program of Shandong Province
  • the Natural Science Foundation of Shandong Province
  • Natural Science Foundation of Shandong Province
  • Key Research and Development Program of Shandong Province

Zitieren

APA

Liu, J., Hu, J., Li, M., Liu, G., Wu, Y., Gao, T., Liu, S., & Liu, X. (2024). Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy. Materials, 17(9), 2022. https://doi.org/10.3390/ma17092022

Vancouver

Liu J, Hu J, Li M, Liu G, Wu Y, Gao T, et al. Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy. Materials. 2024;17(9):2022. doi:10.3390/ma17092022

BibTeX
@article{Liu2024,
  author = {Liu, Jingbin and Hu, Jingyi and Li, Mengyu and Liu, Guiliang and Wu, Yuying and Gao, Tong and Liu, Shushuai and Liu, Xiangfa},
  title = {Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {9},
  pages = {2022},
  doi = {10.3390/ma17092022}
}
Kostenlos starten →