EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Deformation Behavior of an Extruded 7075 Aluminum Alloy at Elevated Temperatures

Tuo Ye, Erli Xia iD, Sawei Qiu, Jie Liu, Huanyu Yue, Jian Tang, Yuanzhi Wu

Materials · 06.03.2024 · 17 (5) · 1210

DOI: 10.3390/ma17051210 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.03.2024. Verfasst von Tuo Ye und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Intelligent Manufacturing and Mechanical Engineering, Hunan Institute of Technology, Hengyang 421002, China. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Scientific Research Fund of Hunan Provincial Education Department of China, National Natural Science Foundation of China, Scientific Research Fund of Hunan Provincial Education Department of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Hot compression tests were conducted to explore the deformation behavior of an extruded 7075 aluminum alloy bar at elevated temperatures. Specimens with 0°, 45°, and 90° angles along the extrusion direction were prepared. The compression temperatures were 300 and 400 °C, and the strain rates ranged from 0.001 to 0.1 s−1. The corresponding microstructures were characterized via OM and TEM, and the macroscopic texture was tested using XRD. The results indicated that the strength of the 7075 alloy decreases with higher compression temperatures and is in a proportional relationship with respect to the strain rate. During high-temperature compression, it is easier to stimulate atomic diffusion in the matrix, which can improve thermal activation abilities and facilitate dynamic recovery and dynamic recrystallization. In addition, the coarsening of precipitates also contributed to dynamic softening. When compressed at 300 °C, the stress levels of the 0° specimens ranked first, and those for the 45° specimens were the lowest. When compressed at 400 °C, the flow stresses of the specimens along three directions were comparable. The anisotropic mechanical behavior can be explained by the fiber grains and brass {011} texture component. However, higher temperature deformation leads to recrystallization, which can weaken the anisotropy of mechanical properties.

Schlagwörter

Stichwörter der Autor:innen

7075 alloyhot deformationmechanical propertiesmicrostructuretexture

Autor:innen und Institutionen

  • School of Intelligent Manufacturing and Mechanical Engineering, Hunan Institute of Technology, Hengyang 421002, China.
  • Research Institute of Automobile Parts Technology, Hunan Institute of Technology, Hengyang 421002, China.

ORCID-Profile: Erli Xia

Förderung

  • the Scientific Research Fund of Hunan Provincial Education Department of China
  • National Natural Science Foundation of China
  • Scientific Research Fund of Hunan Provincial Education Department of China
  • Higher Educational Institutions of Hunan Province

Zitieren

APA

Ye, T., Xia, E., Qiu, S., Liu, J., Yue, H., Tang, J., & Wu, Y. (2024). Deformation Behavior of an Extruded 7075 Aluminum Alloy at Elevated Temperatures. Materials, 17(5), 1210. https://doi.org/10.3390/ma17051210

Vancouver

Ye T, Xia E, Qiu S, Liu J, Yue H, Tang J, et al. Deformation Behavior of an Extruded 7075 Aluminum Alloy at Elevated Temperatures. Materials. 2024;17(5):1210. doi:10.3390/ma17051210

BibTeX
@article{Ye2024,
  author = {Ye, Tuo and Xia, Erli and Qiu, Sawei and Liu, Jie and Yue, Huanyu and Tang, Jian and Wu, Yuanzhi},
  title = {Deformation Behavior of an Extruded 7075 Aluminum Alloy at Elevated Temperatures},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {1210},
  doi = {10.3390/ma17051210}
}
Kostenlos starten →