EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Influence of Contemporary Denture Base Fabrication Methods on Residual Monomer Content, Flexural Strength and Microhardness

Josip Vuksic, Ana Pilipovic iD, Tina Poklepovic Pericic, Josip Kranjcic

Materials · 24.02.2024 · 17 (5) · 1052

DOI: 10.3390/ma17051052 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.02.2024. Verfasst von Josip Vuksic und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Removable Prosthodontics, University of Zagreb School of Dental Medicine, Gunduliceva 5, 10000 Zagreb, Croatia. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

(1)

Background

Digital technologies are available for denture base fabrication, but there is a lack of scientific data on the mechanical and chemical properties of the materials produced in this way. Therefore, the aim of this study was to investigate the residual monomer content, flexural strength and microhardness of denture base materials as well as correlations between investigated parameters. (2)

Methods

Seven denture base materials were used: one conventional heat cured polymethyl methacrylate, one polyamide, three subtractive manufactured materials and two additive manufactured materials. High-performance liquid chromatography was used to determine residual monomer content and the test was carried out in accordance with the specification ISO No. 20795-1:2013. Flexural strength was also determined according to the specification ISO No. 20795-1:2013. The Vickers method was used to investigate microhardness. A one-way ANOVA with a Bonferroni post-hoc test was used for the statistical analysis. The Pearson correlation test was used for the correlation analysis. (3)

Results

There was a statistically significant difference between the values of residual monomer content of the different denture base materials (p < 0.05). Anaxdent pink blank showed the highest value of 3.2% mass fraction, while Polident pink CAD-CAM showed the lowest value of 0.05% mass fraction. The difference between the flexural strength values of the different denture base materials was statistically significant (p < 0.05), with values ranging from 62.57 megapascals (MPa) to 103.33 MPa. The difference between the microhardness values for the different denture base materials was statistically significant (p < 0.05), and the values obtained ranged from 10.61 to 22.86 Vickers hardness number (VHN). A correlation was found between some results for the material properties investigated (p < 0.05). (4)

Conclusions

The selection of contemporary digital denture base manufacturing techniques may affect residual monomer content, flexural strength and microhardness but is not the only criterion for achieving favourable properties.

Schlagwörter

Stichwörter der Autor:innen

computer-aided designcomputer-aided manufacturingdenture basesflexural strengthhardness

Autor:innen und Institutionen

  • Department of Removable Prosthodontics, University of Zagreb School of Dental Medicine, Gunduliceva 5, 10000 Zagreb, Croatia.
  • Department of Prosthodontics, University Hospital Dubrava, Av. Gojka Šuška 6, 10000 Zagreb, Croatia.
  • University of Zagreb Faculty of Mechanical Engineering and Naval Architecture, Ivana Lučića 5, 10000 Zagreb, Croatia.
  • School of Medicine, University of Split, Šoltanska 2, 21000 Split, Croatia.
  • Department of Fixed Prosthodontics, University of Zagreb School of Dental Medicine, Gunduliceva 5, 10000 Zagreb, Croatia.

ORCID-Profile: Ana Pilipovic

Zitieren

APA

Vuksic, J., Pilipovic, A., Poklepovic Pericic, T., & Kranjcic, J. (2024). The Influence of Contemporary Denture Base Fabrication Methods on Residual Monomer Content, Flexural Strength and Microhardness. Materials, 17(5), 1052. https://doi.org/10.3390/ma17051052

Vancouver

Vuksic J, Pilipovic A, Poklepovic Pericic T, Kranjcic J. The Influence of Contemporary Denture Base Fabrication Methods on Residual Monomer Content, Flexural Strength and Microhardness. Materials. 2024;17(5):1052. doi:10.3390/ma17051052

BibTeX
@article{Vuksic2024,
  author = {Vuksic, Josip and Pilipovic, Ana and Poklepovic Pericic, Tina and Kranjcic, Josip},
  title = {The Influence of Contemporary Denture Base Fabrication Methods on Residual Monomer Content, Flexural Strength and Microhardness},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {1052},
  doi = {10.3390/ma17051052}
}
Kostenlos starten →