EUVIMEDEUVIMED entdecken
Crossref

Flexural Properties and Hardness of CAD‐CAM Denture Base Materials

Shaimaa M Fouda iD, Mohammed M Gad iD, Reem Abualsaud iD, Passent Ellakany iD, Hamad S AlRumaih iD, Soban Q Khan, Sultan Akhtar, Faisal D Al-Qarni iD, Fahad A Al-Harbi iD

Journal of Prosthodontics · 2023-04 · 32 (4) · 318-324

DOI: 10.1111/jopr.13535 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 30.05.2022. Verfasst von Shaimaa M Fouda und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia. Hauptthemen laut MEDLINE: Flexural Strength, Denture Bases. Die Arbeit wurde bisher 79-mal zitiert (Crossref) und nennt 37 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To compare flexural strength, elastic modulus, and surface hardness of computer aided design and computer aided manufacturing CAD‐CAM milled, 3D‐printed, and heat‐polymerized denture base resins. Materials and methods A total of 120 specimens were fabricated from heat‐polymerized acrylic resin (HP), milled resin (Avadent and IvoCad), and 3D‐printed resin (ASIGA, FormLabs, and NextDent). The specimens were divided into 6 groups according to the type of denture base material (n = 20/material) (10/flexural properties and 10/hardness). Flexural strength and elastic modulus of the specimens were evaluated by 3‐point bending test and surface hardness by Vickers hardness test. To test flexural properties, the specimens were fabricated according to ISO 20795‐1:2013 standards (64 × 10 × 3.3 ± 0.2 mm). The dimensions for hardness test were 15 × 10 × 2.5 ± 0.2 mm. Scanning electron microscope was used to evaluate the surface morphology of the fractured specimens. The means and standard deviations were calculated, followed by one‐way ANOVA and Tukey post‐hoc test (α = 0.05).

Results

Milled resins showed significantly higher values for flexural strength, elastic modulus, and surface hardness, followed by HP and then 3D‐printed resins ( p < 0.001). Within milled groups, flexural strength of AvaDent was significantly higher than IvoCad ( p < 0.001), while elastic modulus and hardness didn't show significant difference. Within 3D‐printed resins, ASIGA showed the highest flexural strength and elastic modulus, insignificantly with FormLabs ( p = 0.595) and significantly with NextDent ( p = 0.008). ASIGA also showed significantly the highest hardness among the 3D‐printed groups. No significant difference was found between FormLabs and NextDent in flexural strength ( p = 0.357), elastic modulus ( p = 1.00), or surface hardness ( p = 0.987).

Conclusion

CAD‐CAM milled resins had greater flexural properties and hardness compared to heat‐polymerized acrylic resin and 3D‐printed resins. Although 3D‐printed samples showed the lowest values of tested properties, the flexural strength and modulus were above clinically acceptable values.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Flexural StrengthDenture BasesMaterials TestingHardnessComputer-Aided DesignAcrylic ResinsSurface Properties

Stichwörter der Autor:innen

3D-printingCAD-CAMdenture base resinflexural propertiesmilledsurface hardness

Substanzen

Acrylic Resins

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Dental Education, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Biophysics, Institute for Research and Medical Consultations, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.

ORCID-Profile: Shaimaa M Fouda, Mohammed M Gad, Reem Abualsaud, Passent Ellakany, Hamad S AlRumaih, Faisal D Al-Qarni, Fahad A Al-Harbi

Zitieren

APA

Fouda, S. M., Gad, M. M., Abualsaud, R., Ellakany, P., AlRumaih, H. S., Khan, S. Q., Akhtar, S., Al-Qarni, F. D., & Al-Harbi, F. A. (2023). Flexural Properties and Hardness of CAD‐CAM Denture Base Materials. Journal of Prosthodontics, 32(4), 318-324. https://doi.org/10.1111/jopr.13535

Vancouver

Fouda SM, Gad MM, Abualsaud R, Ellakany P, AlRumaih HS, Khan SQ, et al. Flexural Properties and Hardness of CAD‐CAM Denture Base Materials. Journal of Prosthodontics. 2023;32(4):318-324. doi:10.1111/jopr.13535

BibTeX
@article{Fouda2023,
  author = {Fouda, Shaimaa M and Gad, Mohammed M and Abualsaud, Reem and Ellakany, Passent and AlRumaih, Hamad S and Khan, Soban Q and Akhtar, Sultan and Al-Qarni, Faisal D and Al-Harbi, Fahad A},
  title = {Flexural Properties and Hardness of CAD‐CAM Denture Base Materials},
  journal = {Journal of Prosthodontics},
  year = {2023},
  volume = {32},
  number = {4},
  pages = {318--324},
  doi = {10.1111/jopr.13535}
}
Kostenlos starten →