EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices

Martí Calvet iD, Anna Domènech iD, Sergi Vilaró, Toni Meseguer, Lorenzo Bautista

Materials · 04.11.2023 · 16 (21) · 7040

DOI: 10.3390/ma16217040 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 04.11.2023. Verfasst von Martí Calvet und 4 weiteren Autor:innen. Beteiligte Einrichtung: Surface Chemistry Area, Applied Chemistry & Materials Department, Leitat Technological Center, 08225 Terrassa, Barcelona, Spain. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Innovation of Spain.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A new technology consisting of new and sustainable chemical polishing treatment for aluminum components with complex shapes, such as heat exchangers, manifolds, busbars, aerospace devices, etc., manufactured by Additive Manufacturing (AM) technologies is described in this paper. This technology will contribute to the development of a more efficient manufacturing process driven by AM, reinforcing the main idea of AM, which is based on reducing the amount of material and achieving cost savings through smart and improved designs. The present study shows a significant reduction in the surface roughness of consolidated AlSi10Mg metal parts manufactured by the SLM technique after carrying out the new chemical polishing post-process investigated in this work. Roughness values have been measured by mechanical and optical profilometry. The results obtained demonstrate the effectiveness of the chemical polishing, decreasing the roughness by up to 40%, being a reproducible and repeatable post-process. The presence of smut as solid residues on such types of chemical treatments has been also analyzed with XRF and ICP-MS techniques. The results obtained show that Si and Mg precipitates are removed from the metal surface at the last step of the investigated post-process. The percentages of the elements decrease from 25.0% to 8.09% Si and from 0.86% to 0.42% Mg, achieving the alloy smut-free composition on the metal surface. Tensile strength measurements have shown that the post-process described not only maintains the mechanical properties of the bulk material but, in comparison with non-post-processed parts, a slight improvement is observed with respect to the initial values, Young modulus (61.1 GPa to final 62.2 GPa), yield strength (from 236.8 to 246.7 MPa), and tensile strength (from 371.9 to 382.5 MPa) is observed, suggesting that the post-process has positive impact on the printed metal part.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingchemical polishingpost-processroughnessselective laser melting

Autor:innen und Institutionen

  • Surface Chemistry Area, Applied Chemistry & Materials Department, Leitat Technological Center, 08225 Terrassa, Barcelona, Spain.

ORCID-Profile: Martí Calvet, Anna Domènech

Förderung

  • Ministry of Science and Innovation of Spain

Zitieren

APA

Calvet, M., Domènech, A., Vilaró, S., Meseguer, T., & Bautista, L. (2023). Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices. Materials, 16(21), 7040. https://doi.org/10.3390/ma16217040

Vancouver

Calvet M, Domènech A, Vilaró S, Meseguer T, Bautista L. Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices. Materials. 2023;16(21):7040. doi:10.3390/ma16217040

BibTeX
@article{Calvet2023,
  author = {Calvet, Martí and Domènech, Anna and Vilaró, Sergi and Meseguer, Toni and Bautista, Lorenzo},
  title = {Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {21},
  pages = {7040},
  doi = {10.3390/ma16217040}
}
Kostenlos starten →