EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

In Vitro Comparison of Internal and Marginal Adaptation between Printed and Milled Onlays

Oriol Cantó-Navés, Kyra Michels, Oscar Figueras-Alvarez iD, Sandra Fernández-Villar, Josep Cabratosa-Termes iD, Miguel Roig

Materials · 30.10.2023 · 16 (21) · 6962

DOI: 10.3390/ma16216962 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.10.2023. Verfasst von Oriol Cantó-Navés und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Universitat Internacional de Catalunya, 08195 Sant Cugat del Vallès, Barcelona, Spain. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Statement of problem: Nowadays, milling is still the gold standard for fabricating indirect restorations, but to overcome its disadvantages, there are alternatives, such as 3D printing.

Purpose

This study aimed to compare the gaps between the prepared tooth and milled and printed onlays fabricated with the same CAD design. It also aimed to determine the gap reproducibility across onlays fabricated by 3D printing and milling.

Methods

A resin tooth was prepared for an onlay. After scanning the preparation, an onlay was designed with proprietary dental software. Next, 22 onlays were milled in a graphene-reinforced PMMA disc (Group 1), and 22 onlays were 3D-printed with a hybrid composite material (Group 2). After that, all fabricated restorations were scanned and superimposed on the scanned prepared resin tooth. Subsequently, a specific software was used to measure the margin, central, and intaglio-located gap between the milled or printed restoration and the preparation. Finally, measurements were compared with a multifactor analysis of variance.

Results

The results demonstrated that printed onlays (Group 2) adapted better to the prepared tooth than the milled ones (Group 1) (p < 0.05). The comparison of standard deviations showed the better gap reproducibility of printed onlays (p < 0.05).

Conclusion

This study concluded that the printed onlays adapted significantly better to the prepared tooth than the milled onlays. Printed onlays also showed significantly better gap reproducibility.

Schlagwörter

Stichwörter der Autor:innen

3D-printed onlaysgrapheneindirect restorationmilled onlaysresin

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Universitat Internacional de Catalunya, 08195 Sant Cugat del Vallès, Barcelona, Spain.
  • Universitat Internacional de Catalunya, 08195 Sant Cugat del Vallès, Barcelona, Spain.

ORCID-Profile: Oscar Figueras-Alvarez, Josep Cabratosa-Termes

Zitieren

APA

Cantó-Navés, O., Michels, K., Figueras-Alvarez, O., Fernández-Villar, S., Cabratosa-Termes, J., & Roig, M. (2023). In Vitro Comparison of Internal and Marginal Adaptation between Printed and Milled Onlays. Materials, 16(21), 6962. https://doi.org/10.3390/ma16216962

Vancouver

Cantó-Navés O, Michels K, Figueras-Alvarez O, Fernández-Villar S, Cabratosa-Termes J, Roig M. In Vitro Comparison of Internal and Marginal Adaptation between Printed and Milled Onlays. Materials. 2023;16(21):6962. doi:10.3390/ma16216962

BibTeX
@article{CantNavs2023,
  author = {Cantó-Navés, Oriol and Michels, Kyra and Figueras-Alvarez, Oscar and Fernández-Villar, Sandra and Cabratosa-Termes, Josep and Roig, Miguel},
  title = {In Vitro Comparison of Internal and Marginal Adaptation between Printed and Milled Onlays},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {21},
  pages = {6962},
  doi = {10.3390/ma16216962}
}
Kostenlos starten →