EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additively Manufactured Parts from AA2011-T6 Large-Diameter Feedstocks Using Friction Stir Deposition

Naser A Alsaleh iD, Mohamed M El-Sayed Seleman iD, Ahmed M M Hassan iD, Mohamed M Z Ahmed iD, Sabbah Ataya iD, Fahamsyah H Latief, Akrum Abdul-Latif, Mohamed I A Habba iD

Materials · 09.07.2023 · 16 (14) · 4904

DOI: 10.3390/ma16144904 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 09.07.2023. Verfasst von Naser A Alsaleh und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, College of Engineering, Imam Mohammad Ibn Saud Islamic University, Riyadh 11432, Saudi Arabia. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University (IMSIU) through Research Partnership Program, Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University (IMSIU) through the Research Partnership Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The current work investigates the possibility of fabricating additive manufacturing products in solid-state form, from AA2011-T6 of 40 mm diameter rods as a feedstock, using an additive friction stir deposition (A-FSD) technique. The use of large diameter feedstocks, especially high-strength aluminum alloys (2XXX series), is a challenge, as it necessitates high power and the critical selection of the optimal A-FSD parameters, such as feed rate and spindle rotation speed. The study included applying a wide range of spindle rotation speeds, ranging from 400 to 1200 rpm, at three levels of feeding rates of 1, 3, and 5 mm/min. The AA2011-T6 friction stir deposited parts (FSDPs) were visually evaluated. This was followed by an examination of macrostructures through the thickness of the fabricated specimens. The characterization of microstructures was also carried out using optical microscopy and a scanning electron microscope equipped with advanced EDS analysis. Furthermore, the mechanical properties in terms of hardness and compressive strength of the AA2011-T6 base material (BM) and deposited materials were evaluated. Sound, additively manufactured products were successfully fabricated from 40 mm diameter AA2011-T6 feedstocks using the suggested deposition variables of 600 and 800 rpm spindle speeds and feeding rates of 1, 3, and 5 mm/min. The results indicated that the spindle speed and feeding rate govern the quality of the FSDPs. Furthermore, the axial load during the A-FSD process increased with increasing these parameters. In comparison to the AA2011-T6 BM, the additively deposited materials showed a refined grain structure and uniform dispersion of the fragment precipitates in their continuous multi-layers. The reduction ratio in grain size attains 71.56%, 76%, and 81.31% for the FSDPs processed at 800 rpm spindle speed and feeding rates of 1, 3 and 5 mm/min, respectively, compared to the grain size of BM. The Al2Cu and Al7Cu2Fe intermetallics are detected in the AA2011-T6 BM, and their deposited parts are in different shapes of spherical, almost spherical, irregular, and rod-like shapes. The compressive strength and hardness of the deposited parts increased with increasing spindle speed and feeding speeds. At a spindle speed of 800 rpm and a 5 mm/min feeding rate, the higher hardness and compressive strength gained were 85% and 93%, respectively, from that of the AA2011-T6 feedstock.

Schlagwörter

Stichwörter der Autor:innen

AA2011-T6 aluminum alloyadditive friction stir depositionfeed ratemechanical propertiesmicrostructuresolid-state additive manufacturingspindle rotation speed

Autor:innen und Institutionen

  • Department of Mechanical Engineering, College of Engineering, Imam Mohammad Ibn Saud Islamic University, Riyadh 11432, Saudi Arabia.
  • Department of Metallurgical and Materials Engineering, Faculty of Petroleum and Mining Engineering, Suez University, Suez 43512, Egypt.
  • Mechanical Department, Faculty of Technology and Education, Suez University, Suez 43518, Egypt.
  • Mechanical Engineering Department, College of Engineering at Al Kharj, Prince Sattam bin Abdulaziz University, Al Kharj 11942, Saudi Arabia.
  • Department of Mechanical Engineering, Faculty of Engineering and Science, Universitas Nasional, Jakarta 12520, Indonesia.
  • IUT de Tremblay, Université Paris 8, 93290 Tremblay-en-France, France.

ORCID-Profile: Naser A Alsaleh, Mohamed M El-Sayed Seleman, Ahmed M M Hassan, Mohamed M Z Ahmed, Sabbah Ataya, Mohamed I A Habba

Förderung

  • The Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University (IMSIU) through Research Partnership Program
  • Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University (IMSIU) through the Research Partnership Program

Zitieren

APA

Alsaleh, N. A., El-Sayed Seleman, M. M., Hassan, A. M. M., Ahmed, M. M. Z., Ataya, S., Latief, F. H., Abdul-Latif, A., & Habba, M. I. A. (2023). Additively Manufactured Parts from AA2011-T6 Large-Diameter Feedstocks Using Friction Stir Deposition. Materials, 16(14), 4904. https://doi.org/10.3390/ma16144904

Vancouver

Alsaleh NA, El-Sayed Seleman MM, Hassan AMM, Ahmed MMZ, Ataya S, Latief FH, et al. Additively Manufactured Parts from AA2011-T6 Large-Diameter Feedstocks Using Friction Stir Deposition. Materials. 2023;16(14):4904. doi:10.3390/ma16144904

BibTeX
@article{Alsaleh2023,
  author = {Alsaleh, Naser A and El-Sayed Seleman, Mohamed M and Hassan, Ahmed M M and Ahmed, Mohamed M Z and Ataya, Sabbah and Latief, Fahamsyah H and Abdul-Latif, Akrum and Habba, Mohamed I A},
  title = {Additively Manufactured Parts from AA2011-T6 Large-Diameter Feedstocks Using Friction Stir Deposition},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {14},
  pages = {4904},
  doi = {10.3390/ma16144904}
}
Kostenlos starten →