EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fiber Orientation Quantification for Large Area Additively Manufactured Parts Using SEM Imaging

Rifat Ara Nargis, David Abram Jack iD

Polymers · 29.06.2023 · 15 (13) · 2871

DOI: 10.3390/polym15132871 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.06.2023. Verfasst von Rifat Ara Nargis und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Baylor University, Waco, TX 76798, USA. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Baylor University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polymer-based additively manufactured parts are increasing in popularity for industrial applications due to their ease of manufacturing and design form freedom, but their structural and thermal performances are often limited to those of the base polymer system. These limitations can be mitigated by the addition of carbon fiber reinforcements to the polymer matrix, which enhances both the structural performance and the dimensional stability during cooling. The local fiber orientation within the processed beads directly impacts the mechanical and thermal performances, and correlating the orientation to processing parameter variations would lead to better part quality. This study presents a novel approach for analyzing the spatially varying fiber orientation through the use of scanning electron microscopy (SEM). This paper presents the sample preparation procedure including SEM image acquisition and analysis methods to quantify the internal fiber orientation of additively manufactured carbon fiber-reinforced composites. Large area additively manufactured beads with 13% by weight large aspect ratio carbon fiber-reinforced acrylonitrile butadiene styrene (ABS) pellets are the feedstock used in this study. Fiber orientation is quantified using the method of ellipses (MoE), and the spatial change in fiber orientation across the deposited bead cross-section is studied as a function of process parameters including extrusion speed, raster height, and extrusion temperature zones. The results in the present paper show the results from the novel use of SEM to obtain the local fiber orientation, and results show the variation in alignment within the individual processed bead as well as an overall aligned orientation state along the direction of deposition.

Schlagwörter

Stichwörter der Autor:innen

carbon fiber-reinforced polymer matrix compositefiber orientation characterizationlarge area additive manufacturingmethod of ellipsesscanning electron microscopy

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Baylor University, Waco, TX 76798, USA.

ORCID-Profile: David Abram Jack

Förderung

  • Baylor University

Zitieren

APA

Nargis, R. A., & Jack, D. A. (2023). Fiber Orientation Quantification for Large Area Additively Manufactured Parts Using SEM Imaging. Polymers, 15(13), 2871. https://doi.org/10.3390/polym15132871

Vancouver

Nargis RA, Jack DA. Fiber Orientation Quantification for Large Area Additively Manufactured Parts Using SEM Imaging. Polymers. 2023;15(13):2871. doi:10.3390/polym15132871

BibTeX
@article{Nargis2023,
  author = {Nargis, Rifat Ara and Jack, David Abram},
  title = {Fiber Orientation Quantification for Large Area Additively Manufactured Parts Using SEM Imaging},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {13},
  pages = {2871},
  doi = {10.3390/polym15132871}
}
Kostenlos starten →