EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Szymon Kurpiel iD, Krzysztof Zagórski iD, Jacek Cieślik iD, Krzysztof Skrzypkowski iD

Materials · 18.04.2023 · 16 (8) · 3182

DOI: 10.3390/ma16083182 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.04.2023. Verfasst von Szymon Kurpiel und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering and Robotics, AGH University of Science and Technology, Mickiewicza 30 Av., 30-059 Krakow, Poland. Die Arbeit wurde bisher 34-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: AGH University of Science and Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Thin-walled elements are widely used in the aerospace industry, where the aim is to reduce the process time and the weight of the structure while ensuring the sufficient quality of the finished product. Quality is determined by geometric structure parameters and dimensional and shape accuracy. The main problem encountered during the milling of thin-walled elements is the deformation of the product. Despite the various methods available for measuring deformation, more are still being developed. This paper presents selected surface topography parameters and deformation of vertical thin-walled elements during an experiment under controlled cutting conditions for samples from titanium alloy Ti6Al4V. Constant parameters of feed (f), cutting speed (Vc,) and tool diameter (D) were used. Samples were milled using a tool for general-purpose and a tool for high-performance machining, as well as two different machining approaches: with greater involvement of face milling, and cylindrical milling with a constant material removal rate (MRR). For samples with vertical thin walls, the parameters of waviness (Wa, Wz,) and roughness (Ra, Rz) were measured using a contact profilometer in the selected areas on both processed sides. Deformations were determined in selected cross-sections perpendicular and parallel to the bottom of the sample using GOM measurement (GOM—Global Optical Measurement). The experiment showed the possibility of measuring deformations and deflection arrows of thin-walled elements proceeded from titanium alloy using GOM measurement. Differences in selected surface topography parameters and deformations were observed for the machining methods used with an increased cross-section of the cut layer. A sample with a deviation of 0.08 mm from the assumed shape was obtained.

Schlagwörter

Stichwörter der Autor:innen

aerospace industrymillingsurface deformationsurface topographytitanium alloyvertical thin-walled structures

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering and Robotics, AGH University of Science and Technology, Mickiewicza 30 Av., 30-059 Krakow, Poland.
  • Faculty of Civil Engineering and Resource Management, AGH University of Science and Technology, Mickiewicza 30 Av., 30-059 Krakow, Poland.

ORCID-Profile: Szymon Kurpiel, Krzysztof Zagórski, Jacek Cieślik, Krzysztof Skrzypkowski

Förderung

  • AGH University of Science and Technology

Zitieren

APA

Kurpiel, S., Zagórski, K., Cieślik, J., & Skrzypkowski, K. (2023). Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V. Materials, 16(8), 3182. https://doi.org/10.3390/ma16083182

Vancouver

Kurpiel S, Zagórski K, Cieślik J, Skrzypkowski K. Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V. Materials. 2023;16(8):3182. doi:10.3390/ma16083182

BibTeX
@article{Kurpiel2023,
  author = {Kurpiel, Szymon and Zagórski, Krzysztof and Cieślik, Jacek and Skrzypkowski, Krzysztof},
  title = {Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {8},
  pages = {3182},
  doi = {10.3390/ma16083182}
}
Kostenlos starten →