EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Pre-Milling of Cr3C2-25 NiCr Spray Powder on the Fatigue Life of HVOF-Sprayed Coating on ASTM A516 Steel Substrate

Rosivânia da P S Oliveira iD, Gabriel R Cogo, Brenno L Nascimento iD, Matheus M S Reis iD, Antonio Takimi, Sandro Griza iD, Carlos P Bergmann iD

Materials · 14.02.2023 · 16 (4) · 1593

DOI: 10.3390/ma16041593 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 14.02.2023. Verfasst von Rosivânia da P S Oliveira und 6 weiteren Autor:innen. Beteiligte Einrichtung: Post-Graduation Program in Materials Science and Engineering, Federal University of Sergipe, São Cristóvão City 49100-000, SE, Brazil. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Capes/Fapitec/Promob, MCT/ FINEP/ CT-PETRO - Redes Temáticas, MCT/ FINEP/ CT-PETRO-Redes.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of the present investigation is to evaluate the influence of the powder size of Cr3C2-25NiCr spraying powder on the fatigue behavior of HVOF-sprayed coating on the ASTM A516 steel substrate. Conventional commercial Cr3C2-25NiCr spraying powder was previously treated through high-energy milling. The crystallite sizes of milled powders were measured by X-ray diffraction and transmission electronic microscopy. Three different powder formats of the same Cr3C2-25NiCr composite were subjected to HVOF spraying to produce (i) a Milled-Coating (from high-energy milled spray powder), (ii) an Original-Coating (from conventional commercial spray powder), and (iii) a 50%–50% mixture of both (Milled + Original-Coating). The same spraying conditions were adopted for all the assessed cases. The sprayed coatings were investigated through the Knoop hardness test and SEM-EDS analysis. In addition, 3-point bending fatigue tests were conducted at different stress levels up to 107 cycles. The coating morphology and roughness effects on fatigue behavior were analyzed. The Cr3C2-25NiCr milled coating presented a lower fatigue life above the fatigue limit and a higher fatigue limit than other coatings; this outcome could be attributed to its lower surface roughness and finer grain size microstructure.

Schlagwörter

Stichwörter der Autor:innen

Cr3C2-25NiCrHVOFfatiguehigh-energy millingspray powder

Autor:innen und Institutionen

  • Post-Graduation Program in Materials Science and Engineering, Federal University of Sergipe, São Cristóvão City 49100-000, SE, Brazil.
  • Post-Graduation Program in Mining, Metallurgical and Materials Engineering, Engineering School, Federal University of Rio Grande do Sul, Porto Alegre City 90035-190, RS, Brazil.
  • Rijeza Metallurgical Industry, São Leopoldo City 93140-000, RS, Brazil.

ORCID-Profile: Rosivânia da P S Oliveira, Brenno L Nascimento, Matheus M S Reis, Sandro Griza, Carlos P Bergmann

Förderung

  • Capes/Fapitec/Promob
  • MCT/ FINEP/ CT-PETRO - Redes Temáticas
  • MCT/ FINEP/ CT-PETRO-Redes
  • e Capes/Fapitec/Promob

Zitieren

APA

Oliveira, R. D. P. S., Cogo, G. R., Nascimento, B. L., Reis, M. M. S., Takimi, A., Griza, S., & Bergmann, C. P. (2023). Influence of Pre-Milling of Cr3C2-25 NiCr Spray Powder on the Fatigue Life of HVOF-Sprayed Coating on ASTM A516 Steel Substrate. Materials, 16(4), 1593. https://doi.org/10.3390/ma16041593

Vancouver

Oliveira RDPS, Cogo GR, Nascimento BL, Reis MMS, Takimi A, Griza S, et al. Influence of Pre-Milling of Cr3C2-25 NiCr Spray Powder on the Fatigue Life of HVOF-Sprayed Coating on ASTM A516 Steel Substrate. Materials. 2023;16(4):1593. doi:10.3390/ma16041593

BibTeX
@article{Oliveira2023,
  author = {Oliveira, Rosivânia da P S and Cogo, Gabriel R and Nascimento, Brenno L and Reis, Matheus M S and Takimi, Antonio and Griza, Sandro and Bergmann, Carlos P},
  title = {Influence of Pre-Milling of Cr3C2-25 NiCr Spray Powder on the Fatigue Life of HVOF-Sprayed Coating on ASTM A516 Steel Substrate},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {4},
  pages = {1593},
  doi = {10.3390/ma16041593}
}
Kostenlos starten →