EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Microstructure and Alloy Composition on the Machinability of α/β Titanium Alloys

Mostafa M Shehata iD, Shimaa El-Hadad iD, Mahmoud Sherif iD, Khaled M Ibrahim iD, Ahmed I Z Farahat, Helmi Attia iD

Materials · 10.01.2023 · 16 (2) · 688

DOI: 10.3390/ma16020688 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.01.2023. Verfasst von Mostafa M Shehata und 5 weiteren Autor:innen. Beteiligte Einrichtung: Central Metallurgical Research and Development Institute, Helwan P.O. Box 87, Egypt. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Egyptian Government, Egyptian Academy of Scientific Research and Technology, Natural Sciences and Engineering Research Council of Canada.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A comparative study was conducted for the machining of two α/β titanium alloys, namely Ti-6Al-4V (Ti64) and Ti-6Al-7Nb (Ti67), using wire electric discharge machining (WEDM). The influence of cutting speed and cutting mode on the machined surfaces in terms of surface roughness (Ra), recast layer (RL), and micro-hardness have been evaluated. Rough cut (RC) mode at a cutting speed of 50 µm/s resulted in thermal damage; Ra was equal to 5.68 ± 0.44 and 4.52 ± 0.35 µm for Ti64 and Ti67, respectively. Trim-cut mode using seven cuts (TRC-VII) at the same speed decreased the Ra to 1.02 ± 0.20 µm for Ti64 and 0.92 ± 0.10 µm for Ti67. At 100 µm/s, Ra reduced from 2.34 ± 0.28 µm to 0.88 ± 0.12 µm (Ti64), and from 1.42 ± 0.15 µm to 0.90 ± 0.08µm (Ti67) upon changing from TRC-III to TRC-VII. Furthermore, a thick recast layer of 30 ± 0.93 µm for Ti64 and 14 ± 0.68 µm for Ti67 was produced using the rough mode, while TRC-III and TRC-VII modes produced layers of 12 ± 1.31 µm and 5 ± 0.72 µm for Ti64 and Ti67, respectively. Moreover, rough cut and trim cut modes of WEDM played a significant role in promoting the surface hardness of Ti64 and Ti67. By employing the Response Surface Methodology, it was found that the machining mode followed by cutting speed and the interaction between them are the most influential parameters on surface roughness. Finally, mathematical models correlating machining parameters to surface roughness were successfully developed. The results strongly promote the trim-cut mode of WEDM as a promising machining route for two-phase titanium alloys.

Schlagwörter

Stichwörter der Autor:innen

WEDMmodelingsurface characteristicstitanium alloys

Autor:innen und Institutionen

  • Central Metallurgical Research and Development Institute, Helwan P.O. Box 87, Egypt.
  • National Research Council, Montreal, QC H4P 2R2, Canada.
  • Department of Mechanical Engineering, McGill University, Montreal, QC H3A 0C3, Canada.

ORCID-Profile: Mostafa M Shehata, Shimaa El-Hadad, Mahmoud Sherif, Khaled M Ibrahim, Helmi Attia

Förderung

  • Egyptian Government
  • Egyptian Academy of Scientific Research and Technology
  • Natural Sciences and Engineering Research Council of Canada

Zitieren

APA

Shehata, M. M., El-Hadad, S., Sherif, M., Ibrahim, K. M., Farahat, A. I. Z., & Attia, H. (2023). Influence of Microstructure and Alloy Composition on the Machinability of α/β Titanium Alloys. Materials, 16(2), 688. https://doi.org/10.3390/ma16020688

Vancouver

Shehata MM, El-Hadad S, Sherif M, Ibrahim KM, Farahat AIZ, Attia H. Influence of Microstructure and Alloy Composition on the Machinability of α/β Titanium Alloys. Materials. 2023;16(2):688. doi:10.3390/ma16020688

BibTeX
@article{Shehata2023,
  author = {Shehata, Mostafa M and El-Hadad, Shimaa and Sherif, Mahmoud and Ibrahim, Khaled M and Farahat, Ahmed I Z and Attia, Helmi},
  title = {Influence of Microstructure and Alloy Composition on the Machinability of α/β Titanium Alloys},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {2},
  pages = {688},
  doi = {10.3390/ma16020688}
}
Kostenlos starten →