EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigation on Machinability of α/β Titanium Alloys with Different Microstructures

Shimaa El-Hadad iD, Ayman Elsayed iD, Bin Shi, Helmi Attia iD

Materials · 14.11.2023 · 16 (22) · 7157

DOI: 10.3390/ma16227157 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 14.11.2023. Verfasst von Shimaa El-Hadad und 3 weiteren Autor:innen. Beteiligte Einrichtung: Central Metallurgical Research and Development Institute, Helwan P.O. Box 87, Egypt. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Academy of Scientific Research and Technology, Natural Sciences and Engineering Research Council of Canada (NSERC).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the current study, Ti-6Al-4V (Ti64) and Ti-6Al-7Nb (Ti67) alloys were prepared by vacuum arc melting. The produced samples were then subjected to different heat treatment regimes. The evolved microstructures and their corresponding hardness were investigated. Computerized drilling tests using TiAlN-coated high-speed steel bits were performed to assess the machinability of the prepared specimen regarding cutting force, tool wear, and thickness of the deformed layer. It was observed that Ti64 specimens that were water quenched from either α/β or β range contained martensitic phase. In Ti67, samples showed martensite only when water quenched from the β-phase range (1070 °C). Formation of martensite resulted in higher hardness and hence led to higher cutting forces and increased tool wear during the drilling process. Machined samples with higher hardness formed a thicker subsurface deformation area (white layer) and increased burr heights. Surface roughness in Ti64 workpieces was generally higher compared to Ti67 specimens. The coat of the drilling bit was partially attacked in the as-cast specimens, which was evident by elemental N on the machining chips. The machining tool deteriorated further by increasing the workpiece hardness through martensitic formation, where elements such as Cr, V, Fe, etc. that came from the tool steel were detected.

Schlagwörter

Stichwörter der Autor:innen

alpha/beta titanium alloysheat treatmentmachinabilitymicrostructure

Autor:innen und Institutionen

  • Central Metallurgical Research and Development Institute, Helwan P.O. Box 87, Egypt.
  • National Research Council, Montreal, QC H4P 2R2, Canada.
  • Department of Mechanical Engineering, McGill University, Montreal, QC H3A 0C3, Canada.

ORCID-Profile: Shimaa El-Hadad, Ayman Elsayed, Helmi Attia

Förderung

  • Academy of Scientific Research and Technology
  • Natural Sciences and Engineering Research Council of Canada (NSERC)

Zitieren

APA

El-Hadad, S., Elsayed, A., Shi, B., & Attia, H. (2023). Experimental Investigation on Machinability of α/β Titanium Alloys with Different Microstructures. Materials, 16(22), 7157. https://doi.org/10.3390/ma16227157

Vancouver

El-Hadad S, Elsayed A, Shi B, Attia H. Experimental Investigation on Machinability of α/β Titanium Alloys with Different Microstructures. Materials. 2023;16(22):7157. doi:10.3390/ma16227157

BibTeX
@article{ElHadad2023,
  author = {El-Hadad, Shimaa and Elsayed, Ayman and Shi, Bin and Attia, Helmi},
  title = {Experimental Investigation on Machinability of α/β Titanium Alloys with Different Microstructures},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {22},
  pages = {7157},
  doi = {10.3390/ma16227157}
}
Kostenlos starten →