EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Classification of Tool Wear Condition During CNC Cutting Process from Spindle Motor Current Signal Monitoring

Lloyd J. Augustine, Wani J. Morgan, Hsiao-Yeh Chu, Sheng-Jye Hwang, Hsin-Shu Peng

Lubricants · 31.05.2026 · 14 (6) · 227

DOI: 10.3390/lubricants14060227 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Lubricants, online erschienen am 31.05.2026. Verfasst von Lloyd J. Augustine und 4 weiteren Autor:innen. Die Arbeit nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Council, Taiwan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Tool wear in CNC milling increases friction and torque demand at the tool-workpiece interface, which is reflected in spindle motor current. This study develops a non-intrusive tool wear condition classification method using spindle motor current monitoring during practical CNC milling of commercial medium-carbon steel workpieces (JIS S50C/AISI SAE 1050-equivalent; as-received and non-heat-treated; nominal laboratory hardness approximately 4.3 HRC). Experiments were performed on a Tongtai MDV-508 vertical machining center at fixed cutting conditions (3000 rpm spindle speed, 2 mm axial depth of cut, 5 mm cutting width, and 300 mm/min feed rate) using eight TiAlN-coated fine-grain WC–Co solid carbide end mills (10 mm diameter, four flutes; nominal Co binder approximately 10 wt%). An oil-based HS Highstart/HS-SSHS-BH10 cutting fluid was applied through the machine external coolant nozzle in flood mode at an estimated nominal flow rate of approximately 3 L/min and near-room coolant temperature (25 ± 2 °C), and was used as supplied without dilution. A clamp-type AC current sensor was installed on one phase line supplying the spindle motor, and current was acquired using an NI-9221 module at 20 kHz. Cutting intervals were isolated by envelope-based segmentation, concatenated, and divided into 1 s windows (0.5 s overlap) for feature extraction. Three feature sets were evaluated: time-domain statistics, frequency-domain statistics, and an FFT→PCA hybrid representation. Tool states (New, Mid-life, Old) were labeled using post-process surface roughness Ra thresholds supported by microscope observation. The PCA transformation was fitted only on training data and then applied to the held-out test data. A logistic regression classifier achieved 97.44% test accuracy (152/156 windows; 95% Wilson CI: 93.59–99.00%) with the PCA-hybrid features, outperforming time-domain (89.74%) and frequency-domain (94.87%) models. The results support spindle current monitoring as a low-cost approach for quality-aligned tool condition monitoring, while the external validity remains limited to the tested machine, material, tool, coolant, and cutting-parameter combination.

Förderung

  • National Science and Technology Council, Taiwan

Zitieren

APA

Augustine, L. J., Morgan, W. J., Chu, H., Hwang, S., & Peng, H. (2026). Classification of Tool Wear Condition During CNC Cutting Process from Spindle Motor Current Signal Monitoring. Lubricants, 14(6), 227. https://doi.org/10.3390/lubricants14060227

Vancouver

Augustine LJ, Morgan WJ, Chu H, Hwang S, Peng H. Classification of Tool Wear Condition During CNC Cutting Process from Spindle Motor Current Signal Monitoring. Lubricants. 2026;14(6):227. doi:10.3390/lubricants14060227

BibTeX
@article{Augustine2026,
  author = {Augustine, Lloyd J. and Morgan, Wani J. and Chu, Hsiao-Yeh and Hwang, Sheng-Jye and Peng, Hsin-Shu},
  title = {Classification of Tool Wear Condition During CNC Cutting Process from Spindle Motor Current Signal Monitoring},
  journal = {Lubricants},
  year = {2026},
  volume = {14},
  number = {6},
  pages = {227},
  doi = {10.3390/lubricants14060227}
}
Kostenlos starten →