EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Finite Element Analysis of Stress Distribution in Healthy and Restored Mandibular Molars with Zirconia and Lithium Disilicate Crowns Under Vertical and Oblique Loading

Rosa Alicia Hernández-Vázquez iD, Rodrigo Arturo Marquet-Rivera iD, Octavio Alejandro Mastache-Miranda, Karina Gabriela Madrigal-Carrillo, Rosa Adriana Rivera-Díaz iD

Journal of Functional Biomaterials · 14.08.2026 · 17 (8) · 404

DOI: 10.3390/jfb17080404 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 14.08.2026. Verfasst von Rosa Alicia Hernández-Vázquez und 4 weiteren Autor:innen. Beteiligte Einrichtung: División de Mecatrónica, Universidad Politécnica del Valle de México, Avenida Mexiquense sin Número Esquina Avenida Universidad Politécnica, Colonia …. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Instituto Politécnico Nacional, Secretaría de Ciencia, Humanidades, Tecnología e Innovación.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The mechanical compatibility between dental restorative materials and the natural tooth structure is a relevant factor for long-term clinical performance. Although zirconia (yttria-stabilized tetragonal zirconia polycrystal, Y-TZP) and lithium disilicate are widely used for full-coverage crowns, their biomechanical interaction with the underlying dentin and pulp under functional loading remains insufficiently characterized. This study reports a comparative finite element analysis (FEA) of a mandibular first molar under vertical (200 N, axial) and oblique (200 N, 30°) loading, evaluating three configurations: an intact healthy tooth, a zirconia Y-TZP full-coverage crown, and a lithium disilicate full-coverage crown. The three-dimensional geometry was obtained from a cone-beam computed tomography (CBCT) study of a caries-free mandibular first molar, previously described and verified by the present group, and was analyzed in ANSYS Workbench (Static Structural). Von Mises equivalent stress, maximum principal stress and total deformation were obtained for enamel or restoration, dentin, and pulp in each configuration. Zirconia produced the highest stress concentrations in the coronal restoration (88.4 MPa vertical; 174.5 MPa oblique), exceeding the healthy enamel baseline by 57.6% and 89.7%, respectively. Both restorative materials reduced dentin stress relative to the healthy tooth, consistent with the stress-shielding effect driven by elastic-modulus mismatch. Under oblique loading, the maximum principal stress in healthy enamel reached 61.7 MPa, approaching or exceeding the upper bound of the reported tensile strength range (~10–40 MPa) and identifying oblique loading as the more demanding of the two conditions analyzed. Within the limitations of the present finite element model, lithium disilicate demonstrated a more favorable stress distribution, with dentin stress values closer to the intact-tooth baseline. The model does not include a luting cement layer, a periodontal ligament, the dentin–enamel junction, anisotropic tissue behavior or cyclic loading, and no experimental validation was performed; the results are therefore presented as a controlled numerical comparison between three configurations under the specific conditions simulated, and not as direct clinical selection criteria.

Schlagwörter

Stichwörter der Autor:innen

dental biomechanicsfinite element analysisfull-coverage crownlithium disilicatemandibular molarstress distributionstress shieldingzirconia Y-TZP

Autor:innen und Institutionen

  • División de Mecatrónica, Universidad Politécnica del Valle de México, Avenida Mexiquense sin Número Esquina Avenida Universidad Politécnica, Colonia Villa Esmeralda, Tultitlán 54910, Mexico.
  • Posgrado, Facultad de Odontología, Universidad Latinoamericana Campus Norte, Cumbres de Acultzingo 3, Fraccionamiento Los Pirules, Tlalnepantla de Baz 54040, Mexico.
  • Escuela Superior de Comercio y Administración Unidad Tepepan, Instituto Politécnico Nacional, Anillo Periférico Sur Manuel Gómez Morín 4863, Colonia Ampliación Tepepan, Alcaldía Coyoacán, Ciudad de México 16020, Mexico.
  • Escuela Superior de Ingeniería Mecánica y Eléctrica Unidad Culhuacán, Instituto Politécnico Nacional, Avenida Santa Ana 1000, San Francisco Culhuacán, Colonia Culhuacán CTM V, Alcaldía Coyoacán, Ciudad de México 04440,…
  • Unidad Profesional Interdisciplinaria de Energía y Movilidad, Instituto Politécnico Nacional, Avenida Wilfrido Massieu sin Número, Unidad Profesional Adolfo López Mateos, Nueva Industrial Vallejo, Gustavo A. Madero, Ciu…
  • MARMAS Soluciones en Ingeniería e Investigación, Matagalpa 1021A, Residencial Zacatenco, Gustavo A. Madero, Ciudad de México 07369, Mexico.

ORCID-Profile: Rosa Alicia Hernández-Vázquez, Rodrigo Arturo Marquet-Rivera, Rosa Adriana Rivera-Díaz

Förderung

  • Instituto Politécnico Nacional
  • Secretaría de Ciencia, Humanidades, Tecnología e Innovación

Zitieren

APA

Hernández-Vázquez, R. A., Marquet-Rivera, R. A., Mastache-Miranda, O. A., Madrigal-Carrillo, K. G., & Rivera-Díaz, R. A. (2026). Finite Element Analysis of Stress Distribution in Healthy and Restored Mandibular Molars with Zirconia and Lithium Disilicate Crowns Under Vertical and Oblique Loading. Journal of Functional Biomaterials, 17(8), 404. https://doi.org/10.3390/jfb17080404

Vancouver

Hernández-Vázquez RA, Marquet-Rivera RA, Mastache-Miranda OA, Madrigal-Carrillo KG, Rivera-Díaz RA. Finite Element Analysis of Stress Distribution in Healthy and Restored Mandibular Molars with Zirconia and Lithium Disilicate Crowns Under Vertical and Oblique Loading. Journal of Functional Biomaterials. 2026;17(8):404. doi:10.3390/jfb17080404

BibTeX
@article{HernndezVzquez2026,
  author = {Hernández-Vázquez, Rosa Alicia and Marquet-Rivera, Rodrigo Arturo and Mastache-Miranda, Octavio Alejandro and Madrigal-Carrillo, Karina Gabriela and Rivera-Díaz, Rosa Adriana},
  title = {Finite Element Analysis of Stress Distribution in Healthy and Restored Mandibular Molars with Zirconia and Lithium Disilicate Crowns Under Vertical and Oblique Loading},
  journal = {Journal of Functional Biomaterials},
  year = {2026},
  volume = {17},
  number = {8},
  pages = {404},
  doi = {10.3390/jfb17080404}
}
Kostenlos starten →