A Three-Dimensional Finite Element Analysis to Evaluate and Compare Stress Levels and Distribution Patterns in Lithium Disilicate and Zirconia Crowns
European Journal of Dentistry · 01.10.2026 · 20 (04) · 1360-1370
DOI: 10.1055/s-0046-1825876 ↗Kurz gefasst
Fachartikel in der Zeitschrift European Journal of Dentistry, erschienen am 01.10.2026. Verfasst von Ruchika U Mukherjee und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Crown & Bridge, Nitte (Deemed to be University), AB Shetty Memorial Institute of Dental Sciences (ABSMIDS), Mangalur…. Die Arbeit nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
This article aims to assess and compare the patterns of stress distribution and the biomechanical responses of monolithic zirconia and monolithic lithium disilicate crowns of different occlusal thicknesses using three-dimensional (3D) finite element analysis (FEA). A 3D FEA model of a mandibular first molar with all supporting structures was constructed. Eight models were developed to simulate clinically recommended preparation thicknesses for each material, including monolithic zirconia (n = 4; occlusal reductions of 0.5, 1.0, 1.5, and 2.0 mm) and monolithic lithium disilicate (n = 4; nonfunctional/functional cusp reductions ranging from 1.0/1.5 to 2.5/3.0 mm). Two loading scenarios were applied: a 225-N masticatory load at three angulations (0-degree vertical, 45-degree oblique, and 90-degree horizontal) and a 600-N axial maximum bite force. The von Mises stress (VM, used as a scalar yield indicator) and the maximum principal stress (S, used as a tensile fracture predictor for brittle ceramics) were recorded in the crown and in the underlying dentin. Across all thicknesses, zirconia crowns developed higher peak internal VM stress (maximum: 456.8 MPa) but transferred less tensile stress to the underlying dentin (maximum: S ≈ 127 MPa) than lithium disilicate crowns, which transferred greater stress to the dentin (maximum: S ≈ 145.7 MPa). For both materials, non-axial loads (45 and 90 degrees) generated markedly higher stress concentrations (maximum: VM ≈ 457 MPa) than vertical loads (maximum: VM ≈ 278 MPa). Stress distribution within the lithium disilicate crown became visibly more homogeneous with increasing occlusal thickness. Within the limitations of this in silico model, monolithic zirconia exhibited a stress-shielding pattern in which more stress was retained within the crown and less was transmitted to the dentin, whereas lithium disilicate transmitted comparatively more stress to the dentin. Non-axial loading produced the highest stress peaks for both materials in this simulation. Because each material was modeled at the occlusal thickness clinically recommended for it, direct material-versus-material superiority cannot be inferred from these results, and clinical extrapolation should be made with caution.
Autor:innen und Institutionen
- Department of Prosthodontics and Crown & Bridge, Nitte (Deemed to be University), AB Shetty Memorial Institute of Dental Sciences (ABSMIDS), Mangaluru, Karnataka, India.
ORCID-Profile: Shilpa S Dandekeri
Zitieren
APA
Mukherjee, R. U., Dandekeri, S. S., Hegde, C., & Shetty, M. (2026). A Three-Dimensional Finite Element Analysis to Evaluate and Compare Stress Levels and Distribution Patterns in Lithium Disilicate and Zirconia Crowns. European Journal of Dentistry, 20(04), 1360-1370. https://doi.org/10.1055/s-0046-1825876
Vancouver
Mukherjee RU, Dandekeri SS, Hegde C, Shetty M. A Three-Dimensional Finite Element Analysis to Evaluate and Compare Stress Levels and Distribution Patterns in Lithium Disilicate and Zirconia Crowns. European Journal of Dentistry. 2026;20(04):1360-1370. doi:10.1055/s-0046-1825876
BibTeX
@article{Mukherjee2026,
author = {Mukherjee, Ruchika U and Dandekeri, Shilpa S and Hegde, Chethan and Shetty, Manoj},
title = {A Three-Dimensional Finite Element Analysis to Evaluate and Compare Stress Levels and Distribution Patterns in Lithium Disilicate and Zirconia Crowns},
journal = {European Journal of Dentistry},
year = {2026},
volume = {20},
number = {04},
pages = {1360--1370},
doi = {10.1055/s-0046-1825876}
}
EUVIMED