EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical Anisotropy and Fatigue Behavior of 3D-Printed Dentures: A Comparison with CAD/CAM Milled Bases After Thermomechanical Aging

Mohamed Ahmed Alkhodary, Ramy Elmoazen iD, Bandar Awadh Alresheedi iD, Ali Alenezi iD, Naji Alharethi, Rawan Alrethia

Journal of Functional Biomaterials · 15.06.2026 · 17 (6) · 297

DOI: 10.3390/jfb17060297 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 15.06.2026. Verfasst von Mohamed Ahmed Alkhodary und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthetic Dental Sciences, College of Dentistry, Qassim University, Saudi Arabia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To investigate the effect of print orientation (0°, 45°, and 90°) and artificial aging on flexural strength and fatigue resistance of 3D-printed denture bases compared to CAD/CAM milled controls, we fabricated 320 maxillary complete dentures, divided into 8 groups based on the fabrication method: horizontal, oblique, and vertical printing, alongside milled controls. Half of the specimens in each group were pre-conditioned via thermocycling and 240,000 cycles of chewing simulation. All specimens underwent static flexural strength testing and cyclic fatigue testing, followed by SEM fractography. The CAD/CAM milled bases demonstrated the highest mechanical durability, with non-aged specimens peaking at 149.43 ± 5.35 MPa. The horizontally 3D-printed non-aged specimens yielded the highest flexural strength (101.14 ± 4.80 MPa), while vertically printed aged specimens recorded the lowest (70.35 ± 8.18 MPa). Artificial aging degraded flexural strength uniformly across all orientations. Conversely, cyclic loading disproportionately devastated the older people’s vertical group, resulting in a 70% fracture rate. Fractography corroborated these findings, revealing severe interlaminar delamination in vertical builds, contrasting with cohesive, trans-layer fractures in horizontal prints. In conclusion, Horizontal orientation provided improved structural durability; however, CAD/CAM milled dentures remain superior and are recommended for long-term clinical applications.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAM milled basesafter artificial agingchewing simulationdental materialsfatigue resistanceflexural strengthlaboratory technique

Autor:innen und Institutionen

  • Department of Prosthetic Dental Sciences, College of Dentistry, Qassim University, Saudi Arabia.
  • School of Computing, University of Eastern Finland, Yliopistokatu 2, 80100 Joensuu, Finland.

ORCID-Profile: Ramy Elmoazen, Bandar Awadh Alresheedi, Ali Alenezi

Zitieren

APA

Alkhodary, M. A., Elmoazen, R., Alresheedi, B. A., Alenezi, A., Alharethi, N., & Alrethia, R. (2026). Mechanical Anisotropy and Fatigue Behavior of 3D-Printed Dentures: A Comparison with CAD/CAM Milled Bases After Thermomechanical Aging. Journal of Functional Biomaterials, 17(6), 297. https://doi.org/10.3390/jfb17060297

Vancouver

Alkhodary MA, Elmoazen R, Alresheedi BA, Alenezi A, Alharethi N, Alrethia R. Mechanical Anisotropy and Fatigue Behavior of 3D-Printed Dentures: A Comparison with CAD/CAM Milled Bases After Thermomechanical Aging. Journal of Functional Biomaterials. 2026;17(6):297. doi:10.3390/jfb17060297

BibTeX
@article{Alkhodary2026,
  author = {Alkhodary, Mohamed Ahmed and Elmoazen, Ramy and Alresheedi, Bandar Awadh and Alenezi, Ali and Alharethi, Naji and Alrethia, Rawan},
  title = {Mechanical Anisotropy and Fatigue Behavior of 3D-Printed Dentures: A Comparison with CAD/CAM Milled Bases After Thermomechanical Aging},
  journal = {Journal of Functional Biomaterials},
  year = {2026},
  volume = {17},
  number = {6},
  pages = {297},
  doi = {10.3390/jfb17060297}
}
Kostenlos starten →