Primary and Revision Reverse Shoulder Arthroplasty Using Custom-Made 3D-Printed Baseplates for Severe Multiplanar Glenoid Bone Defects: A Retrospective Study of Clinical and Radiographic Outcomes
Journal of Clinical Medicine · 30.08.2025 · 14 (17) · 6153
DOI: 10.3390/jcm14176153 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Clinical Medicine, online erschienen am 30.08.2025. Verfasst von Giovanni Merolla und 6 weiteren Autor:innen. Beteiligte Einrichtung: Shoulder and Elbow Unit, Cervesi Hospital, AUSL Romagna, 47841 Cattolica, Italy. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Background
Severe glenoid bone loss presents a major challenge in both primary and revision reverse shoulder arthroplasty (RSA). Standard implants often fail to achieve reliable fixation in these cases. Custom-made, 3D-printed glenoid components have emerged as a potential solution, offering anatomically tailored fit and fixation. This study evaluates the clinical and radiographic outcomes of custom-made glenoid implants in managing severe glenoid bone loss.
Methods
A retrospective, multicenter study was conducted on 23 shoulders (11 primary and 12 revision RSAs) that received a custom-made glenoid component using the Enovis ProMade System (San Daniele del Friuli, Udine, Italy) between 2017 and 2022, with a minimum follow-up of 24 months. Preoperative planning utilized CT-based 3D modeling to design implants with patient-specific instrumentation. Clinical outcomes (ROM, pain, Constant–Murley score) and radiographic results were assessed. Statistical comparisons were made between primary and revision groups.
Results
Both groups demonstrated significant improvements in shoulder mobility, pain relief, and Constant–Murley scores (all p < 0.001), with no significant differences between primary and revision groups in delta scores. Radiographically, no loosening was observed, with minimal radiolucent lines and low complication rates. Four cases of instability occurred, all in the revision group, with only one requiring conversion to hemiarthroplasty. No differences in radiographic outcomes were observed between groups.
Conclusions
Custom-made glenoid implants provide a reliable solution for severe glenoid bone loss in both primary and revision RSA, yielding consistent functional improvement and implant stability. Further prospective studies with larger cohorts and long-term follow-up are warranted to confirm these findings and assess cost-effectiveness.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Shoulder and Elbow Unit, Cervesi Hospital, AUSL Romagna, 47841 Cattolica, Italy.
- Center of Upper Limb Arthroscopy, Trauma and Minimally Invasive Surgery, Nova Clinic, 47895 Domagnano, San Marino.
- Orthopaedic and Trauma Unit, Principe di Piemonte Hospital, 60019 Senigallia, Italy.
- Orthopedic and Trauma Unit, Sassuolo Hospital, University of Modena and Reggio Emilia, 41049 Sassuolo, Italy.
- Division of Orthopaedic and Trauma Surgery, Villa Verde Hospital, 63900 Fermo, Italy.
ORCID-Profile: Paolo Paladini
Zitieren
APA
Merolla, G., De Filippo, F., Magrini Pasquinelli, F., Micheloni, G. M., Porcellini, G., Paladini, P., & Castricini, R. (2025). Primary and Revision Reverse Shoulder Arthroplasty Using Custom-Made 3D-Printed Baseplates for Severe Multiplanar Glenoid Bone Defects: A Retrospective Study of Clinical and Radiographic Outcomes. Journal of Clinical Medicine, 14(17), 6153. https://doi.org/10.3390/jcm14176153
Vancouver
Merolla G, De Filippo F, Magrini Pasquinelli F, Micheloni GM, Porcellini G, Paladini P, et al. Primary and Revision Reverse Shoulder Arthroplasty Using Custom-Made 3D-Printed Baseplates for Severe Multiplanar Glenoid Bone Defects: A Retrospective Study of Clinical and Radiographic Outcomes. Journal of Clinical Medicine. 2025;14(17):6153. doi:10.3390/jcm14176153
BibTeX
@article{Merolla2025,
author = {Merolla, Giovanni and De Filippo, Francesco and Magrini Pasquinelli, Fabiana and Micheloni, Gian Mario and Porcellini, Giuseppe and Paladini, Paolo and Castricini, Roberto},
title = {Primary and Revision Reverse Shoulder Arthroplasty Using Custom-Made 3D-Printed Baseplates for Severe Multiplanar Glenoid Bone Defects: A Retrospective Study of Clinical and Radiographic Outcomes},
journal = {Journal of Clinical Medicine},
year = {2025},
volume = {14},
number = {17},
pages = {6153},
doi = {10.3390/jcm14176153}
}
EUVIMED