EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Print Orientation and Post-Curing Duration on the Flexural Strength, Flexural Modulus and Vickers Microhardness of a 3D-Printed Occlusal Splint Resin

Mustafa Sahin iD, Suleyman Kutalmış Buyuk iD, Huseyin Simsek iD, Tuncer Akdoğan iD, Safiyenur Bircan iD, Mustafa Serdar Toroglu

Bioengineering · 04.12.2025 · 12 (12) · 1322

DOI: 10.3390/bioengineering12121322 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioengineering, online erschienen am 04.12.2025. Verfasst von Mustafa Sahin und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics, Faculty of Dentistry, Çukurova University, Adana 01250, Türkiye. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) offers precision and efficiency in occlusal splint fabrication; however, the combined influence of build orientation and post-curing duration on the mechanical performance of splint resins remains insufficiently explored. This in vitro experimental study evaluated the effects of three build orientations (0°, 45°, and 90°) and three post-curing protocols (uncured, standard, and extended) on the flexural strength (FS), flexural modulus (FM) and Vickers hardness number (VHN) of a Class IIa biocompatible occlusal splint resin (NextDent Ortho Rigid). A total of 180 specimens were fabricated using a vat polymerization-type 3D printing system. Statistical analyses were conducted using one-way analyses of variance and Tukey’s tests at a significance level of α = 0.05. Both build orientation and post-curing duration significantly affected FS and VHN (p < 0.001). The combination of 45° build orientations and extended post-curing produced the highest FS (169.76 MPa) and FM (7502.17 MPa), exceeding values typically reported for 3D-printed splints, while the 90° orientation with extended curing achieved the highest VHN (21.88). Hardness gains, however, plateaued beyond standard curing, indicating a trade-off between strength and surface hardness. These results demonstrate that print orientation and post-curing time are decisive parameters in optimizing the mechanical performance of 3D-printed occlusal splints. For high-load clinical applications such as bruxism, prioritizing flexural strength over surface hardness may improve appliance longevity, supporting 45° orientation with extended curing as an evidence-based manufacturing approach.

Schlagwörter

Stichwörter der Autor:innen

3D printingVickers hardnessadditive manufacturingbuild orientationflexural modulusflexural strengthocclusal splintpost-curing

Autor:innen und Institutionen

  • Department of Orthodontics, Faculty of Dentistry, Çukurova University, Adana 01250, Türkiye.
  • Department of Orthodontics, Faculty of Dentistry, Ordu University, Ordu 52200, Türkiye.
  • Department of Pedodontics, Faculty of Dentistry, Ordu University, Ordu 52200, Türkiye.
  • Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Çukurova University, Adana 01250, Türkiye.

ORCID-Profile: Mustafa Sahin, Suleyman Kutalmış Buyuk, Huseyin Simsek, Tuncer Akdoğan, Safiyenur Bircan

Zitieren

APA

Sahin, M., Buyuk, S. K., Simsek, H., Akdoğan, T., Bircan, S., & Toroglu, M. S. (2025). Effect of Print Orientation and Post-Curing Duration on the Flexural Strength, Flexural Modulus and Vickers Microhardness of a 3D-Printed Occlusal Splint Resin. Bioengineering, 12(12), 1322. https://doi.org/10.3390/bioengineering12121322

Vancouver

Sahin M, Buyuk SK, Simsek H, Akdoğan T, Bircan S, Toroglu MS. Effect of Print Orientation and Post-Curing Duration on the Flexural Strength, Flexural Modulus and Vickers Microhardness of a 3D-Printed Occlusal Splint Resin. Bioengineering. 2025;12(12):1322. doi:10.3390/bioengineering12121322

BibTeX
@article{Sahin2025,
  author = {Sahin, Mustafa and Buyuk, Suleyman Kutalmış and Simsek, Huseyin and Akdoğan, Tuncer and Bircan, Safiyenur and Toroglu, Mustafa Serdar},
  title = {Effect of Print Orientation and Post-Curing Duration on the Flexural Strength, Flexural Modulus and Vickers Microhardness of a 3D-Printed Occlusal Splint Resin},
  journal = {Bioengineering},
  year = {2025},
  volume = {12},
  number = {12},
  pages = {1322},
  doi = {10.3390/bioengineering12121322}
}
Kostenlos starten →