EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Two-Step Polishing Systems on the Surface Roughness of Bulk Fill Resin Composites: An In-Vitro Study

Gabriela da Silva Chagas, Gildo Coelho Santos, Vahid Dehnavi, Cesar Rogério Pucci, Maria Jacinta Moraes Coelho Santos

Applied Sciences · 28.02.2026 · 16 (5) · 2354

DOI: 10.3390/app16052354 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Sciences, online erschienen am 28.02.2026. Verfasst von Gabriela da Silva Chagas und 4 weiteren Autor:innen. Die Arbeit nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CAPES-PRINT.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the effect of two-step polishing procedures on the surface roughness of bulk fill restorative materials. Disk-shaped specimens (10 × 1.5 mm) were prepared from four resin composites: Filtek One Bulk Fill (3M ESPE) and Tetric PowerFill (Ivoclar Vivadent), both bulk fill nanohybrid composites; X-tra fil LC (Voco), a bulk fill microfilled composite; and Filtek Supreme (3M ESPE), a conventional nanofilled composite used as a control. Polishing was performed using D-Fine Double Diamond, Sof-Lex Diamond, and A.S.A.P. polishers. Each system was applied for 30 s with a slow-speed handpiece at 10,000 rpm under water cooling. Surface roughness (Ra) was measured before and after polishing using a profilometer, with three readings per specimen, and surface morphology was assessed by scanning electron microscopy. Data were analyzed using two-way ANOVA and Tukey’s HSD test (α = 0.05). Significant differences were observed for the interaction between composite type and polishing system (p < 0.001). The lowest Ra value was obtained for Filtek One polished with Sof-Lex Diamond, while the highest surface roughness was observed for X-tra fil LC polished with D-Fine (0.800 ± 0.072 μm). SEM analysis indicated that composites containing larger filler particles exhibited greater surface roughness. In conclusion, surface roughness after polishing was primarily material dependent, with nanofilled composites demonstrating superior polishability compared to materials with larger filler particles.

Förderung

  • CAPES-PRINT

Zitieren

APA

Chagas, G. D. S., Santos, G. C., Dehnavi, V., Pucci, C. R., & Santos, M. J. M. C. (2026). Effect of Two-Step Polishing Systems on the Surface Roughness of Bulk Fill Resin Composites: An In-Vitro Study. Applied Sciences, 16(5), 2354. https://doi.org/10.3390/app16052354

Vancouver

Chagas GDS, Santos GC, Dehnavi V, Pucci CR, Santos MJMC. Effect of Two-Step Polishing Systems on the Surface Roughness of Bulk Fill Resin Composites: An In-Vitro Study. Applied Sciences. 2026;16(5):2354. doi:10.3390/app16052354

BibTeX
@article{Chagas2026,
  author = {Chagas, Gabriela da Silva and Santos, Gildo Coelho and Dehnavi, Vahid and Pucci, Cesar Rogério and Santos, Maria Jacinta Moraes Coelho},
  title = {Effect of Two-Step Polishing Systems on the Surface Roughness of Bulk Fill Resin Composites: An In-Vitro Study},
  journal = {Applied Sciences},
  year = {2026},
  volume = {16},
  number = {5},
  pages = {2354},
  doi = {10.3390/app16052354}
}
Kostenlos starten →