EUVIMEDEUVIMED entdecken
Crossref

Effects of Polishing Systems on Surface Roughness and Color of Single-Shade Resin Composites

D Çölkesen, D Kopuz, G Yersel, N Tekçe

Operative Dentistry · 2026-09 · 51 (5) · 426-440

DOI: 10.2341/25-170-l ↗

Kurz gefasst

Fachartikel in der Zeitschrift Operative Dentistry, 2026-09. Verfasst von D Çölkesen und 3 weiteren Autor:innen. Die Arbeit nennt 36 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

Single-shade resin composites simplify shade selection, but may exhibit different surface and optical responses to finishing and polishing procedures. Limited evidence is available regarding the optimal polishing protocol for these newer materials. The objective of this in vitro study was to evaluate the effects of different polishing systems on the surface roughness and color stability of single-shade resin composites after coffee staining. Methods and Materials: Seven single-shade resin composites were included in this study. A total of 336 specimens (10 mm diameter × 2 mm thick) were prepared (48 specimens per resin composite). The specimens were divided into six subgroups (n = 8) for polishing: Sof-Lex Disc, Sof-Lex Spiral Disc, Enhance & PoGo, Optragloss, Twist Dia, and an unpolished control group. The procedural sequence was polishing, baseline measurements, coffee staining, and final measurements. Surface roughness (Ra) and color parameters (L*, a*, b*) were measured both before and after staining. Surface roughness was measured using a Mitutoyo SJ-410 profilometer, and color measurements were performed using a VITA EasyShade contact-type spectrophotometer. Color differences (ΔE 00 ) were calculated using the CIEDE2000 formula. Data were analyzed with two-way ANOVA and paired-samples t -tests (α < 0.05).

Results

Statistically significant differences were observed among polishing systems for both ΔE 00 and Ra values (both p < 0.001); a significant material × polishing system interaction was detected for surface roughness ( p < 0.001), but not for ΔE 00 ( p = 0.138). For color change, the unpolished control group showed the highest mean ΔE 00 , whereas the spiral aluminum oxide / diamond system (Sof-Lex Spiral) and the two-step diamond spiral system (Twist Dia) showed the lowest mean ΔE 00 . For baseline surface roughness, the unpolished control showed the lowest mean Ra and the diamond cup-and-spiral system (Optragloss) the highest. After staining, the multi-step disc system (Sof-Lex Disc) produced the lowest mean Ra and the two-step rubber-cup diamond system (Enhance & PoGo) the highest. Across resin composites, Vittra APS Unique showed the highest mean color change and Clearfil Majesty ES-2 Universal the lowest. Paired baseline versus post-staining comparisons showed material- and protocol-dependent differences, with significant roughness increases confined mainly to the unpolished control and the Enhance & PoGo group.

Conclusion

The effects of polishing systems on color stability and surface roughness of single-shade resin composites varied depending on both polishing material and resin composite type. Multi-step disc systems and aluminum oxide / diamond spiral systems tended to produce lower post-staining roughness and smaller color change than two-step rubber-cup diamond systems for several of the evaluated resin composites.

Zitieren

APA

Çölkesen, D., Kopuz, D., Yersel, G., & Tekçe, N. (2026). Effects of Polishing Systems on Surface Roughness and Color of Single-Shade Resin Composites. Operative Dentistry, 51(5), 426-440. https://doi.org/10.2341/25-170-l

Vancouver

Çölkesen D, Kopuz D, Yersel G, Tekçe N. Effects of Polishing Systems on Surface Roughness and Color of Single-Shade Resin Composites. Operative Dentistry. 2026;51(5):426-440. doi:10.2341/25-170-l

BibTeX
@article{lkesen2026,
  author = {Çölkesen, D and Kopuz, D and Yersel, G and Tekçe, N},
  title = {Effects of Polishing Systems on Surface Roughness and Color of Single-Shade Resin Composites},
  journal = {Operative Dentistry},
  year = {2026},
  volume = {51},
  number = {5},
  pages = {426--440},
  doi = {10.2341/25-170-l}
}
Kostenlos starten →