EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of the Possibility of Using 3D Printing for Emergency Replacement of Damaged Elements in the Marine Industry

Krzysztof Jasiński, Lech Murawski, Marcin Kluczyk, Jarosław Wierzchowski, Marek Chodnicki, Krzysztof Lipiński, Adam Szeleziński

Applied Sciences · 21.03.2025 · 15 (7) · 3458

DOI: 10.3390/app15073458 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Sciences, online erschienen am 21.03.2025. Verfasst von Krzysztof Jasiński und 6 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study aims to evaluate the feasibility of using Fused Deposition Modeling (FDM)/Fused Filament Fabrication (FFF) 3D printing for the emergency replacement of damaged components in the marine industry, focusing on mechanical properties, dynamic stiffness, and manufacturing efficiency. The authors’ research interests include the application of incremental and hybrid methods for the production of new, fully functional parts that constitute equipment for ships and yachts. The methods described in this paper can also be used to produce replacement parts in emergency conditions when there is a need for a temporary replacement of a damaged component. When testing parts made with 3D printing technology, the authors used modal analysis methods to estimate the dynamic stiffness of bracket support samples. The dynamic analysis of the tested parts was conducted using both the cavity method and the incremental method with FDM and FFF 3D printing. This study focused on determining their resonance curves. Based on these curves, the dynamic stiffness of the samples was calculated. Understanding the changes in dynamic stiffness of 3D printed parts depending on their degree of filling is one of the critical parameters from the point of view of the possibility of the safe operation of parts manufactured with this method. The results show that the dynamic stiffness of 3D printed parts depends significantly on the infill percentage. This article also presents the results of a simplified technical and economic analysis of the bracket support manufacturing samples produced by machining, incremental, and hybrid methods. The quality parameters of the geometric structure of the parts made with the manufacturing methods analyzed in this paper are also compared with each other.

Zitieren

APA

Jasiński, K., Murawski, L., Kluczyk, M., Wierzchowski, J., Chodnicki, M., Lipiński, K., & Szeleziński, A. (2025). Analysis of the Possibility of Using 3D Printing for Emergency Replacement of Damaged Elements in the Marine Industry. Applied Sciences, 15(7), 3458. https://doi.org/10.3390/app15073458

Vancouver

Jasiński K, Murawski L, Kluczyk M, Wierzchowski J, Chodnicki M, Lipiński K, et al. Analysis of the Possibility of Using 3D Printing for Emergency Replacement of Damaged Elements in the Marine Industry. Applied Sciences. 2025;15(7):3458. doi:10.3390/app15073458

BibTeX
@article{Jasiski2025,
  author = {Jasiński, Krzysztof and Murawski, Lech and Kluczyk, Marcin and Wierzchowski, Jarosław and Chodnicki, Marek and Lipiński, Krzysztof and Szeleziński, Adam},
  title = {Analysis of the Possibility of Using 3D Printing for Emergency Replacement of Damaged Elements in the Marine Industry},
  journal = {Applied Sciences},
  year = {2025},
  volume = {15},
  number = {7},
  pages = {3458},
  doi = {10.3390/app15073458}
}
Kostenlos starten →