EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Editorial: “Prospects of 3D printing in fabricating future generations of dental prostheses”

Rua Babaier, Zena Jehad Wally, Abdulaziz Alhotan, Julfikar Haider, Rasha A. Alamoush

Frontiers in Dental Medicine · 19.11.2026 · 7

DOI: 10.3389/fdmed.2026.2048602 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Dental Medicine, online erschienen am 19.11.2026. Verfasst von Rua Babaier und 4 weiteren Autor:innen. Die Arbeit nennt 3 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A first theme is that manufacturing method and post-processing are inseparable from material performance. In their systematic review, Lu et al. reported that the mechanical performance of additively manufactured ceramics approaches that of milled ceramics, particularly for 3Y-TZP, but reliability remains constrained by processing defects, porosity, shrinkage, and layer-orientation effects. Broader reviews of the field have also identified a gap between laboratory promise and clinical reliability (Rezaie et al., 2023). These limitations are particularly important because standardized specimens cannot fully represent the complex geometry, thickness variation, and stress concentrations of a clinical restoration. The same principle extends to restorations fabricated from metals. Alsaif et al. reported that the fabrication technique influenced both surface characteristics and screw-preload retention in three-unit implant-supported cobalt-chromium frameworks: selective laser melting performed better than casting, although milling remained superior. Their finding that roughness did not strongly correlate with preload loss is instructive.Surface topography alone cannot explain clinical behavior; dimensional precision, internal defects, fit, and structural integrity must be considered together.A second theme concerns maintenance and repair, which are essential if printed restorations are to become durable rather than disposable technologies. Robaian evaluated pretreatments for repairing an aged 3D-printed permanent resin and identified diamond-bur roughening, particularly when followed by a universal adhesive, as a promising approach. Air-particle abrasion did not offer the same balance of adhesion and surface preservation. In parallel, Albazroun et al. demonstrated that the preferred surface treatment for denture liners depends on both the liner and denture-base material: sandblasting favored hard-liner bonding, whereas bur roughening resulted in higher bond strength for soft liners bonded to milled and conventional bases. Together, these studies caution against universal surface-treatment protocols. They also broaden the evaluation of additive manufacturing beyond initial strength and accuracy to include ageing, interfacial compatibility, chairside repair, relining, and prosthesis lifetime serviceability.The collection further shows that the clinical value of 3D printing lies in converting biological and procedural requirements into controllable design features. In a clinical comparison of mandibular custom trays, Zhao et al. reported greater prosthodontist satisfaction, better stability and retention, and less manual fabrication time with a CAD and 3D-printing workflow than with light-cured resin or impression-compound techniques. Garcia Zea and Benitez Sellan applied the same logic to the more demanding problem of a flabby ridge. Their digitally designed tray incorporated a defined relief over mobile tissue and enabled a functional closed-mouth impression. These contributions do more than digitize conventional tray production: they make border extension, spacing, relief, and pressure control explicit and reproducible. Nevertheless, the evidence also identifies the next step. Design values based on clinical judgment, such as relief thickness, require validation through larger studies, pressure mapping, and patient-centered outcomes before they can become transferable protocols.A particularly forward-looking contribution moves printed devices from passive guides toward responsive clinical interfaces. Zhao et al. incorporated a mechanoluminescent material into a printable resin to produce an implant guide capable of visible stress-related feedback. The optimized composite combined enhanced mechanical properties with acceptable biocompatibility and was evaluated clinically for implant positioning. Although further validation is needed, this work illustrates how additive manufacturing can integrate geometry with function. Future prosthetic and surgical devices may incorporate sensors, optical feedback, graded stiffness, antimicrobial activity, or other responsive properties, allowing them not only to fit the patient but also to communicate aspects of their performance.Technological readiness must be matched by educational readiness. Alamri et al. reported a satisfactory awareness of 3D design and printing among dental students in Saudi Arabia and a strong interest in further learning, while also identifying accessibility and affordability as barriers.This matters because additive manufacturing is not a single technical step delegated to a printer. Safe use requires understanding data acquisition, design constraints, printer-material compatibility, build orientation, support placement, cleaning and post-curing, quality assurance, and the finished device's limitations. Curricula should therefore progress from awareness to handson, competency-based education and should encourage collaboration among clinicians, technicians, engineers, materials scientists, and manufacturers.Across the research topic, several priorities emerge, echoing calls in the broader prosthodontic literature for standardized protocols and stronger clinical evidence before additive manufacturing is adopted at scale (Alyami, 2024). Studies should report the complete manufacturing chain, including the printer and material, layer thickness, orientation, support strategy, cleaning, postcuring, finishing, and aging procedures, so that results can be reproduced and compared. Laboratory findings should be followed by adequately powered prospective clinical studies that assess survival, complications, maintenance, patient-reported outcomes, cost-effectiveness, and environmental impact. Standardized accuracy and mechanical testing must be linked to clinically meaningful thresholds, while regulatory and quality-management frameworks must evolve with multi-material and multifunctional devices. Interoperability and secure handling of patient data will be equally important as workflows become increasingly cloud-based and assisted by artificial intelligence.The future generation of dental prostheses will not be defined by 3D printing alone, but by the convergence of digital design, advanced biomaterials, intelligent quality control, and clinical evidence. The contributions in this collection capture that transition to some extent. They demonstrate meaningful gains in customization and efficiency, clarify material and maintenance challenges, introduce responsive printed devices, and emphasize the human capabilities required for implementation. The field is now moving beyond technical feasibility toward responsible clinical translation. Achieving that goal will require standardized processes, transparent reporting, long-term validation, and continued collaboration across dentistry, engineering, and materials science. With these foundations, additive manufacturing can support prostheses and devices that are not only more personalized and efficient to produce, but also more predictable, maintainable, and responsive to patients' needs.

Zitieren

APA

Babaier, R., Wally, Z. J., Alhotan, A., Haider, J., & Alamoush, R. A. (2026). Editorial: “Prospects of 3D printing in fabricating future generations of dental prostheses”. Frontiers in Dental Medicine, 7. https://doi.org/10.3389/fdmed.2026.2048602

Vancouver

Babaier R, Wally ZJ, Alhotan A, Haider J, Alamoush RA. Editorial: “Prospects of 3D printing in fabricating future generations of dental prostheses”. Frontiers in Dental Medicine. 2026;7. doi:10.3389/fdmed.2026.2048602

BibTeX
@article{Babaier2026,
  author = {Babaier, Rua and Wally, Zena Jehad and Alhotan, Abdulaziz and Haider, Julfikar and Alamoush, Rasha A.},
  title = {Editorial: “Prospects of 3D printing in fabricating future generations of dental prostheses”},
  journal = {Frontiers in Dental Medicine},
  year = {2026},
  volume = {7},
  doi = {10.3389/fdmed.2026.2048602}
}
Kostenlos starten →