EUVIMEDEUVIMED entdecken
Crossref

Characterization of materials used for 3D printing dental crowns and hybrid prostheses

Pranit V Bora, Akram Sayed Ahmed, Aaron Alford, Kirsten Pitttman, Vinoy Thomas, Nathaniel C Lawson iD

Journal of Esthetic and Restorative Dentistry · 2024-01 · 36 (1) · 220-230

DOI: 10.1111/jerd.13174 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, online erschienen am 26.11.2023. Verfasst von Pranit V Bora und 5 weiteren Autor:innen. Beteiligte Einrichtung: Division of Biomaterials, UAB School of Dentistry, Birmingham, Alabama, USA. Hauptthemen laut MEDLINE: Dental Implants. Die Arbeit wurde bisher 97-mal zitiert (Crossref) und nennt 35 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To compare the filler weight percentage (wt%), filler and resin composition, flexural strength, modulus, and hardness of several 3D‐printed resins to direct and indirect restorative materials. Materials and Methods Four 3D‐printed resins (C&B MFH, Ceramic Crown, OnX, and OnX Tough), one milled resin composite (Lava Ultimate), one conventional composite (Filtek Supreme), and one ceramic (IPS e.max CAD) were evaluated. Filler wt% was determined by the burned ash technique, and filler particle morphology and composition were analyzed by scanning electron microscopy and energy‐dispersive spectroscopy, respectively. Organic resin composition was analyzed by Fourier transform infrared spectroscopy. Three‐point bend flexural strength and modulus of the materials were determined by ISO 4049 or ISO 6872. Vickers microhardness was measured. Data were compared with a one‐way analysis of variance (ANOVA) and Tukey post hoc analysis. Linear regression analysis was performed for filler wt% versus flexural strength, modulus, and hardness.

Results

3D‐printed resins were composed of various sized and shaped silica fillers and various types of methacrylate resins. Significant differences were found among filler wt% with some materials around 3% (C&B MFH), others between 33% and 38% (OnX Tough and OnX), others around 50% (Ceramic Crown), and some around 72% (Filtek Supreme and Lava Ultimate). All 3D‐printed resins had significantly lower flexural strength, modulus, and hardness than the conventional and milled resin composites and ceramic material ( p < 0.001). Filler wt% demonstrated a linear relationship with modulus ( p = 0.013, R 2 = 0.821) and hardness ( p = 0.018, R 2 = 0.787) but not flexural strength ( p = 0.056, R 2 = 0.551).

Conclusions

3D‐printed resins contain from 3% to 50% filler content. Filler wt% alone does not affect flexural strength, but strength may be affected by resin composition as well. Although the 3D‐printed resins had lower flexural strength, modulus, and hardness than milled and conventional composite and ceramic, they demonstrated nonbrittle plastic behavior. Clinical Significance The properties of 3D‐printed resins vary based on their composition, which affects their clinical applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental ImplantsMaterials TestingSurface PropertiesStress, MechanicalDental MaterialsComposite ResinsDental PorcelainPrinting, Three-DimensionalCrowns

Stichwörter der Autor:innen

3D printingfillerhardnessmodulusresinstrength

Substanzen

Dental ImplantsDental MaterialsComposite ResinsDental Porcelain

Autor:innen und Institutionen

  • Division of Biomaterials, UAB School of Dentistry, Birmingham, Alabama, USA.
  • Department of Chemistry, UAB College of Arts and Sciences, Birmingham, Alabama, USA.
  • Department of Mechanical and Materials Engineering, UAB School of Engineering, Birmingham, Alabama, USA.

ORCID-Profile: Nathaniel C Lawson

Zitieren

APA

Bora, P. V., Sayed Ahmed, A., Alford, A., Pitttman, K., Thomas, V., & Lawson, N. C. (2024). Characterization of materials used for 3D printing dental crowns and hybrid prostheses. Journal of Esthetic and Restorative Dentistry, 36(1), 220-230. https://doi.org/10.1111/jerd.13174

Vancouver

Bora PV, Sayed Ahmed A, Alford A, Pitttman K, Thomas V, Lawson NC. Characterization of materials used for 3D printing dental crowns and hybrid prostheses. Journal of Esthetic and Restorative Dentistry. 2024;36(1):220-230. doi:10.1111/jerd.13174

BibTeX
@article{Bora2024,
  author = {Bora, Pranit V and Sayed Ahmed, Akram and Alford, Aaron and Pitttman, Kirsten and Thomas, Vinoy and Lawson, Nathaniel C},
  title = {Characterization of materials used for 3D printing dental crowns and hybrid prostheses},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2024},
  volume = {36},
  number = {1},
  pages = {220--230},
  doi = {10.1111/jerd.13174}
}
Kostenlos starten →