EUVIMEDEUVIMED entdecken
Crossref

Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process

Sanghyun Park, Sion Kim, Sungyoon Lee, Duckbong Seo, Hong Jin Kong, Kyung Hee Hong, Tae Jun Yu

Journal of Laser Applications · 01.11.2026 · 38 (4)

DOI: 10.2351/7.0002274 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Laser Applications, online erschienen am 04.11.2026. Verfasst von Sanghyun Park und 6 weiteren Autor:innen. Die Arbeit nennt 36 Literaturangaben. Gefördert von: Korea Research Institute for Defense Technology Planning and Advancement, Ministry of SMEs and Startups.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study examined through-thickness cutting of 110-mm-thick SUS304–SS400 clad steel (10 mm SUS304/100 mm SS400) using a 6-kW laser oxy-fuel and oxy-flame hybrid (LOXAFH) process. With SUS304 facing the cutting head, oxy-fuel heating formed no measurable entrance kerf. Three laser-assisted oxygen cutting (LASOX) trials failed to penetrate at 6 kW, 0.70 MPa(g) cutting-oxygen pressure, 50 mm min−1, and 10 mm standoff distance. At the same principal settings, one LOXAFH trial achieved full penetration with an O2–liquefied petroleum gas flame and approximately 30 s of stationary preheating. Two additional LOXAFH trials produced through cuts at selected settings. Across these three cuts, top and bottom kerf widths were 6.80–7.75 and 9.55–10.38 mm, respectively. At otherwise nominally identical LOXAFH settings, one 6-kW trial penetrated, whereas eight 3-kW trials failed. At 3 kW, three SS400-up trials penetrated, while eight SUS304-up trials failed. These comparisons indicate that laser power and incident material affected penetration. The matched LASOX–LOXAFH comparison supports feasibility, but the effects of stationary preheating and continuous flame assistance could not be separated. Improved oxygen access remains a possible explanation because in-kerf flow and cut-front motion were not measured. Repeatable penetration was observed at selected conditions, but repeatability at a fixed successful setting for the standard SUS304-up plate remains unverified. Comprehensive cut-quality assessment and suitability for nuclear dismantling require further evaluation.

Förderung

  • Korea Research Institute for Defense Technology Planning and Advancement
  • Ministry of SMEs and Startups

Zitieren

APA

Park, S., Kim, S., Lee, S., Seo, D., Kong, H. J., Hong, K. H., & Yu, T. J. (2026). Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process. Journal of Laser Applications, 38(4). https://doi.org/10.2351/7.0002274

Vancouver

Park S, Kim S, Lee S, Seo D, Kong HJ, Hong KH, et al. Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process. Journal of Laser Applications. 2026;38(4). doi:10.2351/7.0002274

BibTeX
@article{Park2026,
  author = {Park, Sanghyun and Kim, Sion and Lee, Sungyoon and Seo, Duckbong and Kong, Hong Jin and Hong, Kyung Hee and Yu, Tae Jun},
  title = {Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process},
  journal = {Journal of Laser Applications},
  year = {2026},
  volume = {38},
  number = {4},
  doi = {10.2351/7.0002274}
}
Kostenlos starten →