EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparison of physico-mechanical properties of 3D-printed resins used as permanent indirect restoration materials

Merve Arıkan, Serdar Akarsu

Biomaterial Investigations in Dentistry · 20.05.2026 · 13

DOI: 10.2340/biid.v13.46113 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomaterial Investigations in Dentistry, online erschienen am 20.05.2026. Verfasst von Merve Arıkan und 1 weiteren Autor:innen. Beteiligte Einrichtung: Ordu University, Faculty of Dentistry, Department of Restorative Dentistry, Ordu, Turkey. Die Arbeit nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To compare the physico-mechanical properties (microhardness, surface roughness, and flexural strength) of permanent 3D-printed dental resins with those of a resin nanoceramic computer-aided design and computer-aided manufacturing (CAD/CAM) block and a composite resin.

Methods

Four groups were tested: composite resin (Clearfil Majesty Esthetic), resin nanoceramic CAD/CAM block (Cerasmart), and two 3D-printed resins (Saremco Crowntec, VarseoSmile Crown Plus). Disk- and bar-shaped specimens were prepared according to ISO standards. Microhardness (Vickers test), surface roughness (profilometer), and flexural strength (three-point bending test) were evaluated. Data were analyzed using analysis of variance and Tukey post hoc tests (p < 0.05).

Results

Cerasmart showed the highest microhardness (85.53 ± 3.97) and flexural strength (184.45 ± 9.42), while Saremco Crowntec exhibited the lowest microhardness (38.63 ± 2.14). Clearfil Majesty had the highest surface roughness (1.24 ± 0.35). Although the measured flexural strength values of 3D-printed resins exceeded the ISO 4049 minimum threshold, several samples were close to or below the limit.

Conclusions

Within the limitations of this in vitro study, 3D-printed permanent resins exhibited mechanical properties comparable to conventional restorative materials in certain parameters, although inferior hardness values were observed compared to CAD/CAM blocks. Nevertheless, the present findings should be interpreted with caution, and further long-term clinical investigations are necessary before translating these results into clinical practice.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAMdental resinflexural strengthmicrohardnesssurface roughness

Autor:innen und Institutionen

  • Ordu University, Faculty of Dentistry, Department of Restorative Dentistry, Ordu, Turkey.

Zitieren

APA

Arıkan, M., & Akarsu, S. (2026). Comparison of physico-mechanical properties of 3D-printed resins used as permanent indirect restoration materials. Biomaterial Investigations in Dentistry, 13. https://doi.org/10.2340/biid.v13.46113

Vancouver

Arıkan M, Akarsu S. Comparison of physico-mechanical properties of 3D-printed resins used as permanent indirect restoration materials. Biomaterial Investigations in Dentistry. 2026;13. doi:10.2340/biid.v13.46113

BibTeX
@article{Arkan2026,
  author = {Arıkan, Merve and Akarsu, Serdar},
  title = {Comparison of physico-mechanical properties of 3D-printed resins used as permanent indirect restoration materials},
  journal = {Biomaterial Investigations in Dentistry},
  year = {2026},
  volume = {13},
  doi = {10.2340/biid.v13.46113}
}
Kostenlos starten →