EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Shear bond strength of rebonded metal brackets using four light-curing resins: an in vitro study

Verónica Estefanía Pozo, Mauricio Aguirre Balseca, Marjory Elizabeth Vaca Zapata, Karina Maria Salvatore Freitas, Johanna Elizabeth Fiallos Sanchez

Biomaterial Investigations in Dentistry · 16.04.2026 · 13 · 252-260

DOI: 10.2340/biid.v13.45703 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomaterial Investigations in Dentistry, online erschienen am 16.04.2026. Verfasst von Verónica Estefanía Pozo und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Health Sciences, University of the Hemispheres, Quito, Ecuador. Die Arbeit nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Rebonding of orthodontic brackets requires effective surface conditioning to restore adequate adhesive retention.

Objective

To compare the shear bond strength (SBS) of rebonded metal brackets using four light-curing resins. Material and methods: Eighty premolars were allocated to two conditioning protocols (n = 40 per group): G1 – enamel etching with 37% phosphoric acid; G2 – sandblasting of bracket bases followed by enamel etching. Each group was subdivided according to the resin used (n = 10 per subgroup): Orthocem (FGM), Bracespace (3M), Transbond XT (3M), and Z250 (3M). Brackets were bonded, debonded, reconditioned, and rebonded. SBS was tested using a universal testing machine (0.5 mm/min). Data were analyzed using Kruskal–Wallis and Dunn’s post-hoc tests (α = 0.05).

Results

In the acid‐etched group, there was no statistically significant difference in SBS among the four resins (Kruskal–Wallis, p = 0.097). In the sandblasting group, a significant intergroup difference was observed (p = 0.044). Dunn’s post-hoc test identified higher SBS for Bracespace (3M) and Transbond XT (3M) compared with Orthocem (FGM) and Z250 (3M). When comparing conditioning methods within each resin, sandblasting of the bracket bases resulted in significantly higher SBS only for Bracespace and Transbond XT, whereas Orthocem and Z250 showed no significant change.

Conclusions

Rebonding of metal brackets showed comparable SBS among resins after acid etching. However, when the bracket bases were sandblasted, Bracespace and Transbond exhibited significantly higher bond strengths. Surface preparation of the bracket base is therefore a key factor influencing SBS in rebonding procedures.

Schlagwörter

Stichwörter der Autor:innen

bracket adhesion failurebracket reconditioninglight-cure orthodontic adhesivesorthodontic rebondingsandblasting surface treatment

Autor:innen und Institutionen

  • Department of Health Sciences, University of the Hemispheres, Quito, Ecuador.
  • Ingá University Center UNINGA, Maringá, Brazil.

Zitieren

APA

Pozo, V. E., Aguirre Balseca, M., Zapata, M. E. V., Freitas, K. M. S., & Sanchez, J. E. F. (2026). Shear bond strength of rebonded metal brackets using four light-curing resins: an in vitro study. Biomaterial Investigations in Dentistry, 13, 252-260. https://doi.org/10.2340/biid.v13.45703

Vancouver

Pozo VE, Aguirre Balseca M, Zapata MEV, Freitas KMS, Sanchez JEF. Shear bond strength of rebonded metal brackets using four light-curing resins: an in vitro study. Biomaterial Investigations in Dentistry. 2026;13:252-260. doi:10.2340/biid.v13.45703

BibTeX
@article{Pozo2026,
  author = {Pozo, Verónica Estefanía and Aguirre Balseca, Mauricio and Zapata, Marjory Elizabeth Vaca and Freitas, Karina Maria Salvatore and Sanchez, Johanna Elizabeth Fiallos},
  title = {Shear bond strength of rebonded metal brackets using four light-curing resins: an in vitro study},
  journal = {Biomaterial Investigations in Dentistry},
  year = {2026},
  volume = {13},
  pages = {252--260},
  doi = {10.2340/biid.v13.45703}
}
Kostenlos starten →