EUVIMEDEUVIMED entdecken
Crossref

Mechanical and antimicrobial properties of hard denture relining material with surface pre-reacted glass-ionomer filler

Akiho Sunami, Masanao Inokoshi, Muneaki Tamura, Motohiro Uo, Takahiro Wada, Rena Takahashi, Keita Hatano, Hiraku Onuma, Manabu Kanazawa

Journal of Prosthodontic Research · 2026 · 70 (4) · 569-579

DOI: 10.2186/jpr.jpr_d_25_00221 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2026. Verfasst von Akiho Sunami und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan. Hauptthemen laut MEDLINE: Acrylic Resins, Anti-Infective Agents, Denture Liners, Materials Testing. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 45 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: We evaluated the effects of the particle size and content of surface pre-reacted glass-ionomer (S-PRG) filler on the mechanical properties and antimicrobial efficacy of a hard denture relining material. METHODS: S-PRG microfiller (0.8-1 μm; 5, 10, and 20 wt%) and nanofiller (0.3-0.5 μm; 2.5, 5, and 10 wt%) were incorporated into a Shofu denture liner. The control group did not contain S-PRG fillers. The surface morphology (scanning electron microscopy), roughness (confocal scanning laser microscopy; Shapiro-Wilk's test followed by Dunnett or Steel's test), ion release after 24 h immersion in ultrapure water (fluoride, aluminum, borate, sodium, silicate, strontium ions; Shapiro-Wilk's test followed by one-way ANOVA with Tukey's test or Kruskal-Wallis and Dunn's tests), three-point flexural strength (Weibull analysis), shear bond strength after 24 h water immersion or 10,000 thermal cycles (linear mixed-effects model), and antimicrobial activity against Candida albicans (confocal microscopy, Shapiro-Wilk's test followed by Dunnett's or Steel's test) were analyzed and compared. The significance level was set at α = 0.05. RESULTS: Although a higher S-PRG filler content reduced the flexural and bond strengths, it increased the surface roughness and ion release. Groups treated with 10 wt% nanofiller or 20 wt% microfiller displayed significantly inhibited C. albicans adhesion. The nanofiller-containing groups maintained flexural strength comparable to that of the control. CONCLUSIONS: The incorporation of 10 wt% S-PRG nanofiller provided the best balance between antimicrobial efficacy and mechanical performance, indicating that this formulation may be clinically acceptable for use in hard denture relining materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Acrylic ResinsAnti-Infective AgentsDenture LinersMaterials TestingSilicon DioxideDental MaterialsCandida albicansSurface PropertiesShear StrengthParticle SizeFlexural StrengthMicroscopy, Electron, Scanning

Stichwörter der Autor:innen

Candida albicansFlexural strengthIon releaseShear bond strengthSurface roughness

Substanzen

Acrylic Resinsglass ionomerAnti-Infective AgentsSilicon DioxideDental Materials

Autor:innen und Institutionen

  • Department of Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
  • Department of Oral Devices and Materials, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
  • Oral Science Center, Institute of Biomedical Engineering, Institute of Science Tokyo, Tokyo, Japan.
  • Department of Microbiology and Immunology, Nihon University School of Dentistry, Tokyo, Japan.
  • Department of Advanced Biomaterials, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
  • Department of Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.

Zitieren

APA

Sunami, A., Inokoshi, M., Tamura, M., Uo, M., Wada, T., Takahashi, R., Hatano, K., Onuma, H., & Kanazawa, M. (2026). Mechanical and antimicrobial properties of hard denture relining material with surface pre-reacted glass-ionomer filler. Journal of Prosthodontic Research, 70(4), 569-579. https://doi.org/10.2186/jpr.jpr_d_25_00221

Vancouver

Sunami A, Inokoshi M, Tamura M, Uo M, Wada T, Takahashi R, et al. Mechanical and antimicrobial properties of hard denture relining material with surface pre-reacted glass-ionomer filler. Journal of Prosthodontic Research. 2026;70(4):569-579. doi:10.2186/jpr.jpr_d_25_00221

BibTeX
@article{Sunami2026,
  author = {Sunami, Akiho and Inokoshi, Masanao and Tamura, Muneaki and Uo, Motohiro and Wada, Takahiro and Takahashi, Rena and Hatano, Keita and Onuma, Hiraku and Kanazawa, Manabu},
  title = {Mechanical and antimicrobial properties of hard denture relining material with surface pre-reacted glass-ionomer filler},
  journal = {Journal of Prosthodontic Research},
  year = {2026},
  volume = {70},
  number = {4},
  pages = {569--579},
  doi = {10.2186/jpr.jpr_d_25_00221}
}
Kostenlos starten →