EUVIMEDEUVIMED entdecken
Crossref

Effect of non-thermal plasma treatment and resin cements on the bond strength of zirconia ceramics with different yttria concentrations

Deniz Ozturk, Nazmiye Sen iD, Sabire Isler

Biomedical Engineering / Biomedizinische Technik · 2024

DOI: 10.1515/bmt-2023-0336 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomedical Engineering / Biomedizinische Technik, 2024. Verfasst von Deniz Ozturk und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Health Science Institute, University of Istanbul, Istanbul, Türkiye. Hauptthemen laut MEDLINE: Zirconium, Yttrium, Resin Cements, Ceramics. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 30 Literaturangaben. Gefördert von: Bilimsel Araştirma Projeleri Birimi, Istanbul Üniversitesi.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To investigate the effect of different surface treatments and resin cements on the shear bond strength of zirconia ceramics with different yttria concentrations.

Methods

Zirconia blocks characterized by different yttria concentrations [Vita YZ HT (HT), Vita YZ ST (ST) and Vita YZ XT (XT)] were used to prepare disc-shaped specimens (n=252). Specimens prepared to investigate shear bond strength (SBS), water contact angle and surface roughness (Ra) were divided into four subgroups; control (C), sandblasting (S), sandblasting + nonthermal plasma treatment (SNTP) and nonthermal plasma treatment (NTP). For SBS testing, specimens were further divided into two groups (n=108) according to the luting cement used [Panavia F2.0 (P) and Rely X U200 (R)]. The water contact angles were determined by sessile drop technique and Ra was analyzed with optical profilometer. SBS tests were performed in a universal testing machine at a crosshead speed of 0.5 mm/min. The data sets were statistically analyzed with two and three-way ANOVAs followed by post-hoc comparisons ( α =0.05).

Results

The water contact angle and Ra data were significantly affected by surface treatments. The mean Ra values of ST and XT were significantly lower than HT for the surface treatment groups of C and NTP. The SBS values were significantly different among the groups subjected to different surface treatments. The mean SBS values of surface treatment groups (S, SNTP and NTP) when cemented with R were significantly higher than the groups of C (p

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumYttriumResin CementsCeramicsSurface PropertiesPlasma GasesShear StrengthMaterials Testing

Stichwörter der Autor:innen

plasma activationshear bond strengthsurface treatmentszirconia ceramics

Substanzen

ZirconiumYttriumResin Cementszirconium oxideyttriaPlasma Gases

Autor:innen und Institutionen

  • Department of Prosthodontics, Health Science Institute, University of Istanbul, Istanbul, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, University of Istanbul, Istanbul, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, Kent University, Istanbul, Türkiye.

ORCID-Profile: Nazmiye Sen

Förderung

  • Bilimsel Araştirma Projeleri Birimi, Istanbul Üniversitesi

Zitieren

APA

Ozturk, D., Sen, N., & Isler, S. (2024). Effect of non-thermal plasma treatment and resin cements on the bond strength of zirconia ceramics with different yttria concentrations. Biomedical Engineering / Biomedizinische Technik. https://doi.org/10.1515/bmt-2023-0336

Vancouver

Ozturk D, Sen N, Isler S. Effect of non-thermal plasma treatment and resin cements on the bond strength of zirconia ceramics with different yttria concentrations. Biomedical Engineering / Biomedizinische Technik. 2024. doi:10.1515/bmt-2023-0336

BibTeX
@article{Ozturk2024,
  author = {Ozturk, Deniz and Sen, Nazmiye and Isler, Sabire},
  title = {Effect of non-thermal plasma treatment and resin cements on the bond strength of zirconia ceramics with different yttria concentrations},
  journal = {Biomedical Engineering / Biomedizinische Technik},
  year = {2024},
  doi = {10.1515/bmt-2023-0336}
}
Kostenlos starten →