EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The internal and marginal adaptation of lithium disilicate endocrowns fabricated using intra and extraoral scanners: An in-vitro study

Marzieh Akhlaghian, Amir-Alireza Khaledi, Seyed Ali Mosaddad, Sana Dabiri, Rashin Giti iD, Farhad Kadkhodae, Shabnam Gholami

PLOS ONE · 16.04.2024 · 19 (4) · e0301361

DOI: 10.1371/journal.pone.0301361 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, online erschienen am 16.04.2024. Verfasst von Marzieh Akhlaghian und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran. Hauptthemen laut MEDLINE: Computer-Aided Design, Dental Porcelain. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 87 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

The impression technique highly influences the adaptation of ceramic restorations. Not enough information is available to compare the marginal (MF) and internal fit (IF) of endocrowns fabricated with various digitization techniques. Therefore, this in-vitro study aimed to compare the MF and IF of lithium disilicate (LDS) endocrowns fabricated through direct and indirect digital scanning methods. Materials and methods One extracted maxillary molar was used to fabricate endocrowns. The digitization of the model was performed with (G1) direct scanning (n = 10) utilizing an intraoral scanner (IOS), (G2) indirectly scanning the conventional impression taken from the model using the same IOS (n = 10), (G3) indirectly digitalizing the obtained impression using an extraoral scanner (EOS) (n = 10), and (G4) scanning the poured cast using the same EOS (n = 10). The MF and IF of the endocrowns were measured using the replica method and a digital stereomicroscope. The Kruskal-Wallis test was used to analyze data.

Results

The studied groups differed significantly (p

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignDental PorcelainCeramicsMolarDental Prosthesis DesignDental Impression Technique

Substanzen

lithia disilicateDental Porcelain

Autor:innen und Institutionen

  • Department of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.
  • Department of Research Analytics, Saveetha Institute of Medical and Technical Sciences, Saveetha Dental College and Hospitals, Saveetha University, Chennai, India.
  • Faculty of Odontology, Department of Conservative Dentistry and Bucofacial Prosthesis, Complutense University of Madrid, Madrid, Spain.
  • Student Research Committee, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran.

ORCID-Profile: Rashin Giti

Zitieren

APA

Akhlaghian, M., Khaledi, A. A., Mosaddad, S. A., Dabiri, S., Giti, R., Kadkhodae, F., & Gholami, S. (2024). The internal and marginal adaptation of lithium disilicate endocrowns fabricated using intra and extraoral scanners: An in-vitro study. PLOS ONE, 19(4), e0301361. https://doi.org/10.1371/journal.pone.0301361

Vancouver

Akhlaghian M, Khaledi AA, Mosaddad SA, Dabiri S, Giti R, Kadkhodae F, et al. The internal and marginal adaptation of lithium disilicate endocrowns fabricated using intra and extraoral scanners: An in-vitro study. PLOS ONE. 2024;19(4):e0301361. doi:10.1371/journal.pone.0301361

BibTeX
@article{Akhlaghian2024,
  author = {Akhlaghian, Marzieh and Khaledi, Amir-Alireza and Mosaddad, Seyed Ali and Dabiri, Sana and Giti, Rashin and Kadkhodae, Farhad and Gholami, Shabnam},
  title = {The internal and marginal adaptation of lithium disilicate endocrowns fabricated using intra and extraoral scanners: An in-vitro study},
  journal = {PLOS ONE},
  year = {2024},
  volume = {19},
  number = {4},
  pages = {e0301361},
  doi = {10.1371/journal.pone.0301361}
}
Kostenlos starten →