EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The effect of repeated porcelain firings on the marginal fit of millable and conventional casting alloys

Rashin Giti iD, Mahdi Hosseinpour Aghaei, Farhad Mohammadi

PLOS ONE · 2023

DOI: 10.1371/journal.pone.0275374 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2023. Verfasst von Rashin Giti und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran. Hauptthemen laut MEDLINE: Dental Porcelain, Computer-Aided Design. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Vice-Chancellor for Research, Shiraz University of Medical Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The durability of dental restorations is highly determined by an accurate marginal fit, which is in turn affected by the high temperature of porcelain firing. Information is inadequate about the marginal adaptation of metal-ceramic restorations fabricated by soft metal milling technologies after repeated firings. This study aimed to compare the effect of repeated ceramic firings on the marginal fit of copings fabricated from cobalt-chromium through soft metal milling and a conventional nickel-chromium casting alloy. A single standard brass die was designed, machined, and scanned, based on which, 20 frameworks were designed and fabricated through either soft metal milling or conventional casting ( n = 10 per group) and porcelain veneered. The vertical marginal fit of the metal copings was measured after 3, 5, and 7 firing cycles by using a digital microscope on 16 points around the finish line of the metal die at ×80 magnification. The data were analyzed through repeated measures ANOVA and independent t-test ( α = 0.05). The marginal fit of neither metal group was significantly affected by the number of firing cycles ( P = 0.747). However, the marginal discrepancy was statistically lower in the soft metal milling group than that in the casting group ( P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainComputer-Aided DesignMetal Ceramic AlloysChromium AlloysCobaltChromiumDental Prosthesis Design

Substanzen

Dental PorcelainMetal Ceramic AlloysChromium AlloysCobaltChromium

Autor:innen und Institutionen

  • Department of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.
  • Student Research Committee, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.
  • Department of Pharmaceutics, School of Pharmacy, Shahid Sadoughi University of Medical Sciences and Health Care Services, Yazd, Iran.

ORCID-Profile: Rashin Giti

Förderung

  • Vice-Chancellor for Research, Shiraz University of Medical Sciences

Zitieren

APA

Giti, R., Hosseinpour Aghaei, M., & Mohammadi, F. (2023). The effect of repeated porcelain firings on the marginal fit of millable and conventional casting alloys. PLOS ONE. https://doi.org/10.1371/journal.pone.0275374

Vancouver

Giti R, Hosseinpour Aghaei M, Mohammadi F. The effect of repeated porcelain firings on the marginal fit of millable and conventional casting alloys. PLOS ONE. 2023. doi:10.1371/journal.pone.0275374

BibTeX
@article{Giti2023,
  author = {Giti, Rashin and Hosseinpour Aghaei, Mahdi and Mohammadi, Farhad},
  title = {The effect of repeated porcelain firings on the marginal fit of millable and conventional casting alloys},
  journal = {PLOS ONE},
  year = {2023},
  doi = {10.1371/journal.pone.0275374}
}
Kostenlos starten →