EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Marginal fit of 3-unit implant-supported fixed partial dentures: Influence of pattern fabrication method and repeated porcelain firings

Rashin Giti iD, Pardis Farrahi

PLOS ONE · 2024

DOI: 10.1371/journal.pone.0301799 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2024. Verfasst von Rashin Giti und 1 weiteren Autor:innen. Beteiligte Einrichtung: Oral and Dental Diseases Research Center, Faculty of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran. Hauptthemen laut MEDLINE: Dental Porcelain, Computer-Aided Design. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Vice-Chancellor for Research, Shiraz University of Medical Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Marginal fit significantly impacts the long-term success of dental restorations. Different pattern fabrication methods, including hand-waxing, milling, or 3D printing, may affect restorations accuracy. The effect of porcelain firing cycles on the marginal fit of metal-ceramic restorations remains controversial, with conflicting findings across studies.

Purpose

The aim was to evaluate the potential effects of multiple porcelain firings (3, 5, 7 cycles) as well as pattern fabrication method (conventional hand-waxing, milling, and 3D printing) on the marginal adaptation of 3-unit implant-supported metal-ceramic fixed partial dentures. It was hypothesized that neither the wax pattern fabrication method nor repeated ceramic firings would significantly affect the marginal adaptation of metal-ceramic crowns.

Methods

In this in-vitro study, 30 Cobalt-Chromium alloy frameworks were fabricated based on pattern made through three techniques: conventional hand-waxing, CAD-CAM milling, and CAD-CAM 3D printing ( n = 10 per group). Sixteen locations were marked on each abutment to measure the vertical marginal gap at four stages: before porcelain veneering and after 3, 5, and 7 firing cycles. The vertical marginal gap was measured using direct microscopic technique at ×80 magnification. Mean vertical marginal gap values were calculated and two-way ANOVA and Tukey’s post hoc tests were used for inter-group comparisons (α = 0.05).

Results

The 3D printing group showed significantly lower ( P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainComputer-Aided DesignPrinting, Three-DimensionalDenture, Partial, FixedMetal Ceramic AlloysDental Prosthesis DesignCrowns

Substanzen

Dental PorcelainMetal Ceramic Alloys

Autor:innen und Institutionen

  • Oral and Dental Diseases Research Center, Faculty of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.
  • Department of Prosthodontics, Faculty of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.
  • Student Research Committee, Faculty of Dentistry, Shiraz University of Medical Sciences, Shiraz, Fars, Iran.

ORCID-Profile: Rashin Giti

Förderung

  • Vice-Chancellor for Research, Shiraz University of Medical Sciences

Zitieren

APA

Giti, R., & Farrahi, P. (2024). Marginal fit of 3-unit implant-supported fixed partial dentures: Influence of pattern fabrication method and repeated porcelain firings. PLOS ONE. https://doi.org/10.1371/journal.pone.0301799

Vancouver

Giti R, Farrahi P. Marginal fit of 3-unit implant-supported fixed partial dentures: Influence of pattern fabrication method and repeated porcelain firings. PLOS ONE. 2024. doi:10.1371/journal.pone.0301799

BibTeX
@article{Giti2024,
  author = {Giti, Rashin and Farrahi, Pardis},
  title = {Marginal fit of 3-unit implant-supported fixed partial dentures: Influence of pattern fabrication method and repeated porcelain firings},
  journal = {PLOS ONE},
  year = {2024},
  doi = {10.1371/journal.pone.0301799}
}
Kostenlos starten →