EUVIMEDEUVIMED entdecken
Crossref

Understanding the dust generation and machinability characteristics during cryogenic drilling of carbon fiber-reinforced plastics

Gökhan Kayabaşı, Uğur Köklü, Sezer Morkavuk, Khaled Giasin, Ayhan Etyemez

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering · 29.05.2026

DOI: 10.1177/09544089261455659 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, online erschienen am 29.05.2026. Verfasst von Gökhan Kayabaşı und 4 weiteren Autor:innen. Die Arbeit nennt 59 Literaturangaben. Gefördert von: Karamanoğlu Mehmetbey Üniversitesi.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Carbon fiber-reinforced plastics are used across various industries, particularly in aviation, owing to their exceptional properties, necessitating secondary operations such as drilling, milling, and turning to achieve the desired shape. Machining of carbon fiber-reinforced plastics can induce thermal and mechanical damage in the laminate, resulting in the fragmentation of fibers and matrix into fine particles, creating powder-like chips that negatively impact operator health. In this study, particle dust contamination generated during the drilling of carbon fiber-reinforced plastics under dry and cryogenic conditions and using different cutting parameters was measured and evaluated. The results showed that, in general, dust formation was less at 1000 r/min, but the damage in the hole was greater. On the other hand, at low spindle speeds of 1000 rpm, while cryogenic machining increased the thrust force by 31–36% and torque by 19–162%, it also led to a reduction in dust generation by 18.26–38.91% at 1000 r/min and an improvement in roughness (6–12%). Interestingly, a significant increase in dust generation (58.5% to 249%) was observed under cryogenic conditions at higher spindle speeds of 9000 r/min, possibly due to liquid nitrogen vapor levitating additional dust particles into the atmosphere. The results indicate that while cryogenic machining can be considered an environmentally friendly cooling process, it can become the primary source of increasing mass concentrations of airborne particles when drilling at high spindle speeds.

Förderung

  • Karamanoğlu Mehmetbey Üniversitesi

Zitieren

APA

Kayabaşı, G., Köklü, U., Morkavuk, S., Giasin, K., & Etyemez, A. (2026). Understanding the dust generation and machinability characteristics during cryogenic drilling of carbon fiber-reinforced plastics. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. https://doi.org/10.1177/09544089261455659

Vancouver

Kayabaşı G, Köklü U, Morkavuk S, Giasin K, Etyemez A. Understanding the dust generation and machinability characteristics during cryogenic drilling of carbon fiber-reinforced plastics. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2026. doi:10.1177/09544089261455659

BibTeX
@article{Kayaba2026,
  author = {Kayabaşı, Gökhan and Köklü, Uğur and Morkavuk, Sezer and Giasin, Khaled and Etyemez, Ayhan},
  title = {Understanding the dust generation and machinability characteristics during cryogenic drilling of carbon fiber-reinforced plastics},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering},
  year = {2026},
  doi = {10.1177/09544089261455659}
}
Kostenlos starten →