Processability and mechanical characterisation of short fique fibre/PLA sustainable composites manufactured via injection moulding
Journal of Reinforced Plastics and Composites · 19.11.2026
DOI: 10.1177/07316844261510147 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Reinforced Plastics and Composites, online erschienen am 19.11.2026. Verfasst von Boomadevi Shanmugam und 8 weiteren Autor:innen. Die Arbeit nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidad Nacional de Colombia, Global Challenge Research Fund - Scottish Funding Council.
Abstract (Originalsprache)
Short natural fibres are widely used as reinforcement in polymer matrices due to their ecological and economic advantages, with properties tailored to specific applications. The use of biodegradable matrices with low-cost natural fibres reduces environmental impact and material costs. However, high fibre content in such composites requires a balance between processability and mechanical performance. In this study, polylactic acid (PLA) composites containing 40.5 vol% randomly oriented fique fibres are fabricated by injection moulding. The influence of 0.3 wt% zinc (Zn), magnesium (Mg), and aluminium (Al) stearates on processability, thermal stability, and mechanical properties are evaluated. The incorporation of metallic stearates improves flowability, with PLA-F-Mg exhibiting the highest MFI (31.96 g/10min), corresponding to a 61.3% increase relative to unmodified composites. However, stearates reduce tensile strength, with PLA-F-Zn exhibiting the lowest value (21.40 MPa). Thermal analysis shows that Zn stearate causes the highest reduction in thermal stability (308.81°C), whereas Mg stearate maintains comparatively higher thermal stability (355.74°C). The addition of fique fibres reduces the impact strength, although Mg-loaded composite provides the highest value among modified composites. SEM analysis reveals fibre pull-out, interfacial debonding, and longer crack formation, particularly in Zn-loaded composites, indicating inefficient stress transfer. Overall, Mg stearate provides the most balanced improvement in processability, thermal stability, and mechanical performance, demonstrating its potential for improving the processability of high fibre content fique/PLA composites.
Förderung
- Universidad Nacional de Colombia
- Global Challenge Research Fund - Scottish Funding Council
Zitieren
APA
Shanmugam, B., Arif, Z. U., Kalali, E. N., Yang, L., Lotfian, S., Meza, J., Vargas, J., Vryonis, O., & Jalalvand, M. (2026). Processability and mechanical characterisation of short fique fibre/PLA sustainable composites manufactured via injection moulding. Journal of Reinforced Plastics and Composites. https://doi.org/10.1177/07316844261510147
Vancouver
Shanmugam B, Arif ZU, Kalali EN, Yang L, Lotfian S, Meza J, et al. Processability and mechanical characterisation of short fique fibre/PLA sustainable composites manufactured via injection moulding. Journal of Reinforced Plastics and Composites. 2026. doi:10.1177/07316844261510147
BibTeX
@article{Shanmugam2026,
author = {Shanmugam, Boomadevi and Arif, Zia Ullah and Kalali, Ehsan Naderi and Yang, Liu and Lotfian, Saeid and Meza, Juan and Vargas, Johnattan and Vryonis, Orestis and Jalalvand, Meisam},
title = {Processability and mechanical characterisation of short fique fibre/PLA sustainable composites manufactured via injection moulding},
journal = {Journal of Reinforced Plastics and Composites},
year = {2026},
doi = {10.1177/07316844261510147}
}
EUVIMED