EUVIMEDDescoperă EUVIMED
Crossref

Influence of Dentin Bonding and Interfacial Adhesion on the Flexural Properties of a 4 Mol% Yttria Partially Stabilized Zirconia

Francesco De Angelis, Matteo Buonvivere, Camilla Mancini, Giuseppe Daniele Rondoni, Mirco Vadini, Camillo D'Arcangelo

The International Journal of Prosthodontics · 2025

DOI: 10.11607/ijp.9283 ↗

At a glance

Journal article in The International Journal of Prosthodontics, 2025. Written by Francesco De Angelis and 5 co-authors. Major MEDLINE topics: Zirconium, Yttrium, Dentin, Dental Bonding.

RezumatSubjectsDate bibliograficeCiteRelated studies

Abstract (original language)

PURPOSE: 4 mol% yttria partially stabilized zirconia (4Y-PSZ) offers improved translucency compared to 3% tetragonal polycrystalline zirconia, but it lacks transformation toughening, which may affect its flexural strength. Because adhesive luting was shown to improve mechanical performance of all-ceramic materials, this research evaluated the influence of different cements on the three-point flexural strength of 4Y-PSZ bonded to bovine dentin. MATERIALS AND METHODS: A total of 30 1-mm-thick dentin slices were obtained from bovine incisors, paired with 1-mm-thick 4Y-PSZ slices, and then divided into three groups (n = 10) based on the cement investigated: 10-MDP-free self-adhesive resin cement (SA), 10-MDP-based adhesive resin cement (MDP-A), and conventional glass-ionomer cement (GI). After luting, the obtained assemblies were cut to obtain 1-mm-wide bar-shaped specimens, which were subjected to the three-point bending test. Fracture loads and flexural strength were recorded, and the modes of failure were analyzed. RESULTS: The highest fracture load and flexural strength were observed in the MDP-A group (76.5 N and 401.5 MPa), followed by the SA group (62.3 N and 326.8 MPa). The GI group exhibited the lowest values (45.6 N and 239.5 MPa). MDP-A group samples predominantly exhibited concurrent dentin and zirconia fractures without debonding, while in the SA and GI groups a frequent incidence of debonding at the interface was observed. CONCLUSIONS: Adhesive cementation enhances the flexural strength of 4Y-PSZ bonded to bovine dentin, with the 10-MDP-based resin cement yielding the best performance. Effective adhesive techniques could improve the mechanical performance of 4Y-PSZ restorations, making them more reliable for clinical applications.

Subjects

MeSH terms (MEDLINE)

ZirconiumYttriumDentinDental BondingDentin-Bonding AgentsDental MaterialsCattleAnimalsFlexural StrengthResin CementsMaterials TestingDental Stress AnalysisGlass Ionomer CementsSurface Properties

Substances

ZirconiumYttriumResin CementsDentin-Bonding Agentszirconium oxideGlass Ionomer CementsyttriaDental Materials

Cite

APA

De Angelis, F., Buonvivere, M., Mancini, C., Rondoni, G. D., Vadini, M., & D'Arcangelo, C. (2025). Influence of Dentin Bonding and Interfacial Adhesion on the Flexural Properties of a 4 Mol% Yttria Partially Stabilized Zirconia. The International Journal of Prosthodontics. https://doi.org/10.11607/ijp.9283

Vancouver

De Angelis F, Buonvivere M, Mancini C, Rondoni GD, Vadini M, D'Arcangelo C. Influence of Dentin Bonding and Interfacial Adhesion on the Flexural Properties of a 4 Mol% Yttria Partially Stabilized Zirconia. The International Journal of Prosthodontics. 2025. doi:10.11607/ijp.9283

BibTeX
@article{DeAngelis2025,
  author = {De Angelis, Francesco and Buonvivere, Matteo and Mancini, Camilla and Rondoni, Giuseppe Daniele and Vadini, Mirco and D'Arcangelo, Camillo},
  title = {Influence of Dentin Bonding and Interfacial Adhesion on the Flexural Properties of a 4 Mol% Yttria Partially Stabilized Zirconia},
  journal = {The International Journal of Prosthodontics},
  year = {2025},
  doi = {10.11607/ijp.9283}
}
Start for free →