EUVIMEDDescoperă EUVIMED
Vergleichsstudie

Monomer Release from 3D-Printed Crown Resin, Hybrid CAD/CAM Block, Bulk-Fill, Indirect, and Direct Composites in Resin-Based Posterior Restorations: An In Vitro Study

Zehra Süsgün Yildirim, Sevde Gül Batmaz

The International Journal of Prosthodontics · 2025

DOI: 10.11607/ijp.9199 ↗

At a glance

Vergleichsstudie in The International Journal of Prosthodontics, 2025. Written by Zehra Süsgün Yildirim and 1 co-authors. Major MEDLINE topics: Crowns, Composite Resins, Dental Materials, Dental Prosthesis Design.

RezumatSubjectsDate bibliograficeCiteRelated studies

Abstract (original language)

PURPOSE: To evaluate resin-based posterior restorative materials by comparing the release of BPA, TEGDMA, HEMA, UDMA, and Bis-GMA monomers at 1 hour, 3 days, and 1 month. MATERIALS AND METHODS: Five different materials were used in this study: Cerasmart (CS), Gradia-Plus Indirect (GI), G-ænial Posterior (GP), Formlabs 3D-Permanent Crown (FPC), and SonicFill 3 (SF). A total of 90 specimens 8 × 8 × 2 mm3 in size were prepared from all the materials. The specimens were immersed in a 75% ethanol/25% water solution and placed in an incubator for 1 hour, 3 days, and 1 month, after which the solutions were analyzed using high-performance liquid chromatography (HPLC). For the comparisons of data with normal distribution among the five different materials, repeated-measures ANOVA followed by Bonferroni post-hoc tests were applied (α = .05). RESULTS: Except for BPA release in the FPC material, all other materials exhibited an increasing release of monomers over time (P < .001). At all the measured time points, the material with the lowest monomer release was CS, while the highest release was observed in GP. The GI material exhibited the statistically significant highest release of BPA, TEGDMA, and Bis-GMA (P < .001), while the highest UDMA and HEMA release was observed in the GP material (P < .001). CONCLUSIONS: The highest monomer release was observed for UDMA (0.8%) from the GP material at the end of 1 month. However, the monomer release from all examined materials remained well below the clinically acceptable range (1.5% to 5%).

Subjects

MeSH terms (MEDLINE)

CrownsComposite ResinsDental MaterialsDental Prosthesis DesignMethacrylatesPolyethylene GlycolsPolymethacrylic AcidsMaterials TestingIn Vitro TechniquesBisphenol A-Glycidyl MethacrylatePolyurethanesBenzhydryl CompoundsHumansPhenolsChromatography, High Pressure LiquidBisphenol A Compounds

Substances

Composite ResinsMethacrylatesPolyethylene GlycolsPolymethacrylic Acidstriethylene glycol dimethacrylateBisphenol A-Glycidyl Methacrylateurethane dimethacrylate luting resinhydroxyethyl methacrylateDental MaterialsPolyurethanes

Cite

APA

Yildirim, Z. S., & Batmaz, S. G. (2025). Monomer Release from 3D-Printed Crown Resin, Hybrid CAD/CAM Block, Bulk-Fill, Indirect, and Direct Composites in Resin-Based Posterior Restorations: An In Vitro Study. The International Journal of Prosthodontics. https://doi.org/10.11607/ijp.9199

Vancouver

Yildirim ZS, Batmaz SG. Monomer Release from 3D-Printed Crown Resin, Hybrid CAD/CAM Block, Bulk-Fill, Indirect, and Direct Composites in Resin-Based Posterior Restorations: An In Vitro Study. The International Journal of Prosthodontics. 2025. doi:10.11607/ijp.9199

BibTeX
@article{Yildirim2025,
  author = {Yildirim, Zehra Süsgün and Batmaz, Sevde Gül},
  title = {Monomer Release from 3D-Printed Crown Resin, Hybrid CAD/CAM Block, Bulk-Fill, Indirect, and Direct Composites in Resin-Based Posterior Restorations: An In Vitro Study},
  journal = {The International Journal of Prosthodontics},
  year = {2025},
  doi = {10.11607/ijp.9199}
}
Start for free →