EUVIMEDEUVIMED entdecken
Crossref

Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations

Deniz Yılmaz, Gülce Çakmak, Mehmet Esad Güven, Stefano Pieralli, Hyung-In Yoon, Marta Revilla-León, Burak Yilmaz

International Journal of Prosthodontics · 21.02.2024 · 37 (7) · S133-S141

DOI: 10.11607/ijp.8847 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Prosthodontics, online erschienen am 21.02.2024. Verfasst von Deniz Yılmaz und 6 weiteren Autor:innen. Hauptthemen laut MEDLINE: Flexural Strength, Polymethyl Methacrylate. Die Arbeit wurde bisher 18-mal zitiert (Crossref).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: To evaluate the flexural strength (FS) and microhardness of various CAD/CAM restorative materials intended for definitive use. The effect of hydrothermal aging on the mechanical properties of these materials was also investigated. MATERIALS AND METHODS: A total of 210 bar-shaped specimens (17 × 4 × 1.5 mm ± 0.02 mm) were fabricated via either subtractive manufacturing (SM) methods-reinforced composite resin (SM-CR), polymer-infiltrated ceramic network (SM-PICN), fine-structured feldspathic ceramic (SMFC), nanographene-reinforced polymethyl methacrylate (PMMA; SM-GPMMA), PMMAbased resin (SM-PMMA)-or additive manufacturing (AM) methods with urethane acrylate-based resins (AM-UA1 and AM-UA2). Specimens were then divided into two subgroups (nonaged or hydrothermal aging; n = 15). A three-point flexural strength test was performed, and five specimens from the nonaged group were submitted to microhardness testing. Specimens were subjected to 10,000 thermal cycles, and the measurements were repeated. RESULTS: Regardless of aging, SM-CR had the highest FS (P < .001), followed by SM-GPMMA (P ≤ .042). In nonaged groups, AM-UA2 had a lower FS than all other materials except SM-FC (P = 1.000). In hydrothermal aging groups, AM specimens had lower FS values than other materials, except SM-PMMA. With regard to microhardness, there was no significant difference found between any of the tested materials (P ≥ .945) in the nonaged and hydrothermal aging groups. CONCLUSIONS: The effect of hydrothermal aging on FS varied depending on the type of restorative material. Regardless of aging condition, SM-CR showed the highest FS values, whereas SM-FC had the highest microhardness. Hydrothermal aging had no significant influence on the microhardness of the tested materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Flexural StrengthPolymethyl MethacrylateDental MaterialsComposite ResinsPolymersMaterials TestingSurface PropertiesComputer-Aided Design

Substanzen

Polymethyl MethacrylateDental MaterialsComposite ResinsPolymers

Zitieren

APA

Yılmaz, D., Çakmak, G., Güven, M. E., Pieralli, S., Yoon, H. I., Revilla-León, M., & Yilmaz, B. (2024). Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations. International Journal of Prosthodontics, 37(7), S133-S141. https://doi.org/10.11607/ijp.8847

Vancouver

Yılmaz D, Çakmak G, Güven ME, Pieralli S, Yoon HI, Revilla-León M, et al. Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations. International Journal of Prosthodontics. 2024;37(7):S133-S141. doi:10.11607/ijp.8847

BibTeX
@article{Ylmaz2024,
  author = {Yılmaz, Deniz and Çakmak, Gülce and Güven, Mehmet Esad and Pieralli, Stefano and Yoon, Hyung-In and Revilla-León, Marta and Yilmaz, Burak},
  title = {Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations},
  journal = {International Journal of Prosthodontics},
  year = {2024},
  volume = {37},
  number = {7},
  pages = {S133--S141},
  doi = {10.11607/ijp.8847}
}
Kostenlos starten →