Effect of Hydrogen Peroxide–Based Bleaching Agents on the Color Dimensions and Surface Roughness of Different Milled Restorative Dental Materials
The International Journal of Prosthodontics · 2024
DOI: 10.11607/ijp.8539 ↗At a glance
Journal article in The International Journal of Prosthodontics, 2024. Written by Jaime Velasco Luque and 4 co-authors. Major MEDLINE topics: Surface Properties, Color, Hydrogen Peroxide, Dental Materials. Cited 1 times so far (Crossref).
Abstract (original language)
PURPOSE: To compare the color dimensions, color discrepancies (ΔE00), and surface roughness of milled materials before and after application of a bleaching agent. MATERIALS AND METHODS: A total of 10 extracted molars were obtained. Each tooth was cut in transverse sections to create disks (3-mm thick, 10-mm diameter; control group). Disk specimens of eight materials (n = 10 per group) were fabricated: polymethyl methacrylate (PMMA) interim material (PMMA-Telio group), two resin nanoceramics (RNC-Ultimate group and RNC-Cerasmart group), two hybrid ceramics (HC-Shofu group and HC-Enamic group), lithium disilicate (LD-Emax group), zirconia-reinforced glass ceramic (ZGC-Suprinity group), and zirconia (Zr-InCeram group). Color measurements were obtained using a spectrophotometer before and after applying 35% hydrogen peroxide-based bleaching agent. Pre- and postbleaching surface roughness (Sa) analyses were completed using a profilometer. RESULTS: Significant L*, a*, b*, and ΔE00 value differences were found (P < .05). Color discrepancies (ΔE00) ranged from 0.30 ± 0.14 to 4.82 ± 0.10. The highest color discrepancies were measured on the PMMA-Telio group, while the lowest color discrepancies were computed for ZGC-Suprinity, RNCUltimate, and RNC-Cerasmart. Significant surface roughness differences were found (P < .05). The largest increase of surface roughness values between the pre- and postbleaching measurements was obtained in the PMMA-Telio group with a mean ΔSa value of 4.73 ± 3.02, while the largest decrease of surface roughness values between the pre- and postbleaching measurements was obtained in the Zr-InCeram group with a mean ΔSa value of -1.58 ± 0.10. CONCLUSIONS: The milled materials showed significant pre- and postbleaching color and surface roughness discrepancies.
Subjects
MeSH terms (MEDLINE)
Substances
Cite
APA
Luque, J. V., Zubizarreta-Macho, Á., Bartolomé, J. F., Kois, J. C., & Revilla-León, M. (2024). Effect of Hydrogen Peroxide–Based Bleaching Agents on the Color Dimensions and Surface Roughness of Different Milled Restorative Dental Materials. The International Journal of Prosthodontics. https://doi.org/10.11607/ijp.8539
Vancouver
Luque JV, Zubizarreta-Macho Á, Bartolomé JF, Kois JC, Revilla-León M. Effect of Hydrogen Peroxide–Based Bleaching Agents on the Color Dimensions and Surface Roughness of Different Milled Restorative Dental Materials. The International Journal of Prosthodontics. 2024. doi:10.11607/ijp.8539
BibTeX
@article{Luque2024,
author = {Luque, Jaime Velasco and Zubizarreta-Macho, Álvaro and Bartolomé, José F and Kois, John C and Revilla-León, Marta},
title = {Effect of Hydrogen Peroxide–Based Bleaching Agents on the Color Dimensions and Surface Roughness of Different Milled Restorative Dental Materials},
journal = {The International Journal of Prosthodontics},
year = {2024},
doi = {10.11607/ijp.8539}
}
EUVIMED