EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Impact of Reduced Blade Count and Tip Clearance Variation on the Flow Field of Axial Compressor Blade Rows

Robert Kaltofen, Martin Lange, Enrique Sielaff, Patrick Grothe, Bernd Becker, Ronald Mailach

Journal of Turbomachinery · 01.09.2026 · 148 (10)

DOI: 10.1115/1.4072543 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Turbomachinery, online erschienen am 15.09.2026. Verfasst von Robert Kaltofen und 5 weiteren Autor:innen. Die Arbeit nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium fur Wirtschaft und Technologie.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aerodynamic design of axial compressor blades requires a careful trade-off between aerodynamic loading and efficiency. Fewer blades increase the aerodynamic load on each blade, while a reduced rotor blade count can lower profile losses due to the smaller number of wakes—potentially improving efficiency. It can also intensify secondary flows because of the higher local loading. To evaluate these opposing effects during preliminary design, three-dimensional Reynolds-averaged Navier–Stokes (RANS) simulations remain common practice, although they are known to have weaknesses when predicting secondary flow phenomena. This article presents experimental results from a four-stage, low-speed research compressor. Tests were carried out with two different blade counts and with both small and enlarged tip clearances to validate the numerical models. The rotor blade count was reduced by roughly 30%, and the rotor stagger angle was increased to maintain the design-point pressure ratio and mass flow while compensating the stronger deviation. The study focuses on the influence of these changes on the tip clearance vortex of the rotor blades; the measured data are used to validate simulations that support deeper analysis. The chosen reduction in blade count led to an overall efficiency gain and a markedly lower sensitivity to tip clearance increases. Although the higher loading produces a steeper tip leakage vortex, the operating range is not substantially narrowed. The larger blade pitch allows the vortex to traverse the passage with reduced interaction with adjacent blades. These results improve understanding of tip clearance vortex behavior and can inform future compressor design.

Förderung

  • Bundesministerium fur Wirtschaft und Technologie

Zitieren

APA

Kaltofen, R., Lange, M., Sielaff, E., Grothe, P., Becker, B., & Mailach, R. (2026). The Impact of Reduced Blade Count and Tip Clearance Variation on the Flow Field of Axial Compressor Blade Rows. Journal of Turbomachinery, 148(10). https://doi.org/10.1115/1.4072543

Vancouver

Kaltofen R, Lange M, Sielaff E, Grothe P, Becker B, Mailach R. The Impact of Reduced Blade Count and Tip Clearance Variation on the Flow Field of Axial Compressor Blade Rows. Journal of Turbomachinery. 2026;148(10). doi:10.1115/1.4072543

BibTeX
@article{Kaltofen2026,
  author = {Kaltofen, Robert and Lange, Martin and Sielaff, Enrique and Grothe, Patrick and Becker, Bernd and Mailach, Ronald},
  title = {The Impact of Reduced Blade Count and Tip Clearance Variation on the Flow Field of Axial Compressor Blade Rows},
  journal = {Journal of Turbomachinery},
  year = {2026},
  volume = {148},
  number = {10},
  doi = {10.1115/1.4072543}
}
Kostenlos starten →