EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Multilaboratory Study Toward Standardizing Spine Testing: Evaluating Reproducibility and Temporal Changes in Lumbar Spine Surrogates

Jenna Wahbeh, Jeremy G Loss, Emma C Coltoff, Siril Teja Dukkipati iD, Sophia N Sangiorgio iD, Edward Ebramzadeh, William R Walsh iD, Tian Wang iD, Matthew Pelletier iD, G Bryan Cornwall iD, Brian P Kelly, Philip J Brown und 4 weitere

Journal of Biomechanical Engineering · 01.09.2026 · 148 (9)

DOI: 10.1115/1.4072253 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomechanical Engineering, online erschienen am 17.07.2026. Verfasst von Jenna Wahbeh und 15 weiteren Autor:innen. Beteiligte Einrichtung: Department of Bioengineering, University of California, Los Angeles, Los Angeles, CA 90095; The J. Vernon Luck, Sr., M.D. Orthopaedic Research Center…. Hauptthemen laut MEDLINE: Lumbar Vertebrae, Materials Testing, Mechanical Phenomena, Laboratories. Die Arbeit nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Composite spine surrogates have been designed to address the challenges of biomechanical testing using cadavers; however, their biofidelity and reproducibility among laboratories remain unknown. This study aimed to evaluate interlaboratory reproducibility and temporal variability of a composite lumbar spine surrogate under standardized pure moment testing conditions. Nine lumbar (L2–L5) spine surrogates were tested in seven laboratories with expertise in spinal biomechanics. Each specimen underwent pure moment testing in flexion–extension, lateral bending, and axial rotation (±7.5 N·m), using each lab's respective test setup and procedure. The spines were divided into two groups and shipped in opposite testing sequences to control for order effects. Qualitative condition was recorded following each round. Differences in range of motion (ROM) among specimens and laboratories were assessed. Additionally, changes in ROM were evaluated as a function of testing sequence. Consistent and progressive damage to the facet joints was noted, but only minimal degradation was observed to the other structural components. Specimen ROM increased significantly over time, in all three rotations, flexion/extension, lateral bending, and axial rotation, after repeated loading (p < 0.05). Independent of time, interspecimen variability was high, with almost all specimens differing from each other in flexion and axial rotation (p < 0.05). Conceptually, composite spine models offer several advantages over cadaveric specimens. However, this study identified limitations in durability, performance, and reproducibility with the aim of advising future surrogate modeling research and advancing efforts toward standardized spine testing protocols.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Lumbar VertebraeMaterials TestingMechanical PhenomenaLaboratoriesReproducibility of ResultsHumansRange of Motion, ArticularBiomechanical PhenomenaTime FactorsReference Standards

Autor:innen und Institutionen

  • Department of Bioengineering, University of California, Los Angeles, Los Angeles, CA 90095; The J. Vernon Luck, Sr., M.D. Orthopaedic Research Center, The Luskin Orthopaedic Institute for Children in Alliance with UCLA,…
  • BioRobotics Core, Cleveland Clinic Research, Cleveland Clinic, 2111 East 96th Street, Cleveland, OH 44106.
  • Department of Biomedical Engineering, Wake Forest School of Medicine, Winston-Salem, NC 27101.
  • Musculoskeletal Biomechanics Research Lab, Department of Mechanical Engineering, McGill University, 845 Sherbrooke Street W (163), Montréal, QC H3A 0C3, Canada; Orthopaedic Research Lab, Montreal General Hospital, 1650…
  • The J. Vernon Luck, Sr., M.D. Orthopaedic Research Center, The Luskin Orthopaedic Institute for Children in Alliance with UCLA, Los Angeles, CA 90009; Department of Orthopaedic Surgery, University of California, Los Ang…
  • Surgical and Orthopaedic Research Laboratories (SORL), Prince of Wales Clinical School, UNSW Sydney, Kensington 2031, Australia.

ORCID-Profile: Siril Teja Dukkipati, Sophia N Sangiorgio, William R Walsh, Tian Wang, Matthew Pelletier, G Bryan Cornwall

Zitieren

APA

Wahbeh, J., Loss, J. G., Coltoff, E. C., Dukkipati, S. T., Sangiorgio, S. N., Ebramzadeh, E., Walsh, W. R., Wang, T., Pelletier, M., Cornwall, G. B., Kelly, B. P., Brown, P. J., Driscoll, M., Chastain, K. L., Meyers, K. N., & Colbrunn, R. (2026). A Multilaboratory Study Toward Standardizing Spine Testing: Evaluating Reproducibility and Temporal Changes in Lumbar Spine Surrogates. Journal of Biomechanical Engineering, 148(9). https://doi.org/10.1115/1.4072253

Vancouver

Wahbeh J, Loss JG, Coltoff EC, Dukkipati ST, Sangiorgio SN, Ebramzadeh E, et al. A Multilaboratory Study Toward Standardizing Spine Testing: Evaluating Reproducibility and Temporal Changes in Lumbar Spine Surrogates. Journal of Biomechanical Engineering. 2026;148(9). doi:10.1115/1.4072253

BibTeX
@article{Wahbeh2026,
  author = {Wahbeh, Jenna and Loss, Jeremy G and Coltoff, Emma C and Dukkipati, Siril Teja and Sangiorgio, Sophia N and Ebramzadeh, Edward and Walsh, William R and Wang, Tian and Pelletier, Matthew and Cornwall, G Bryan and Kelly, Brian P and Brown, Philip J and Driscoll, Mark and Chastain, Kalle L and Meyers, Kathleen N and Colbrunn, Robb},
  title = {A Multilaboratory Study Toward Standardizing Spine Testing: Evaluating Reproducibility and Temporal Changes in Lumbar Spine Surrogates},
  journal = {Journal of Biomechanical Engineering},
  year = {2026},
  volume = {148},
  number = {9},
  doi = {10.1115/1.4072253}
}
Kostenlos starten →