EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Laser Polishing of Vertically Oriented FDM-PLA Components: Influence of Laser Power and Polishing Speed on Surface Topography and Mechanical Response

Gabriel Stolárik iD, Radoslav Vandžura iD, Róbert Ropovík iD, Damián Peti iD, Matúš Geľatko iD

Polymers · 21.11.2025 · 17 (23) · 3096

DOI: 10.3390/polym17233096 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 21.11.2025. Verfasst von Gabriel Stolárik und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Manufacturing Technologies with a Seat in Prešov, Technical University of Kosice, Štúrova St. 31, 080 01 Prešov, Slovakia. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency, Ministry of Education, Research, Development, and Youth of the Slovak Republic., Operational Program Integrated Infrastructure funded by the ERDF..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser polishing represents a promising post-processing method for FDM-printed parts, enabling targeted manipulation of their surface topography and the associated functional properties. Despite extensive research in this field, no experimental investigation has yet addressed the configuration with vertical build orientation, which is critical in terms of interlayer stress transfer. Therefore, this study focuses on CO2 laser polishing of vertically printed PLA specimens at power levels of 10 and 12 W and polishing speeds of vf = 200, 400, and 600 mm·s−1, with a constant transverse displacement of 0.1 mm. The results showed that both laser power and polishing speed have a significant influence on the surface topography and mechanical properties of the samples. The lowest roughness values, Ra = 10.24 ± 0.14 µm at 10 W and Ra = 12.20 ± 0.43 µm at 12 W, were achieved at the highest polishing speed of vf = 600 mm·s−1; however, these still exceeded the roughness of the reference unpolished sample (Ra = 9.02 ± 0.21 µm). The increase in roughness was attributed to the formation of relief structures caused by insufficient overlap of laser passes, orthogonal to the printing-induced surface orientation. These reliefs further acted as local stress concentrators, resulting in a decrease in mechanical performance of up to 9% in comparison with the reference specimen. At 10 W, the surface profile was dominated by Rv > Rp, similar to the reference sample, whereas at 12 W, the opposite trend (Rp > Rv) was observed—attributed to more intense subsurface melting and valley filling by the melt pool. Therefore, the findings clearly confirm that the critical factor is the energy distribution and transverse displacement of the laser polishing paths, where improper parameter settings may visually improve the surface while structurally weakening it. These findings highlight the need for further research, focused on the precise optimization of the polishing trajectory and the energy distribution for vertically oriented samples.

Schlagwörter

Stichwörter der Autor:innen

laser polishinglaser powerpost-processingroughnessscanning speedstrength

Autor:innen und Institutionen

  • Faculty of Manufacturing Technologies with a Seat in Prešov, Technical University of Kosice, Štúrova St. 31, 080 01 Prešov, Slovakia.

ORCID-Profile: Gabriel Stolárik, Radoslav Vandžura, Róbert Ropovík, Damián Peti, Matúš Geľatko

Förderung

  • Slovak Research and Development Agency
  • Ministry of Education, Research, Development, and Youth of the Slovak Republic.
  • Operational Program Integrated Infrastructure funded by the ERDF.

Zitieren

APA

Stolárik, G., Vandžura, R., Ropovík, R., Peti, D., & Geľatko, M. (2025). Laser Polishing of Vertically Oriented FDM-PLA Components: Influence of Laser Power and Polishing Speed on Surface Topography and Mechanical Response. Polymers, 17(23), 3096. https://doi.org/10.3390/polym17233096

Vancouver

Stolárik G, Vandžura R, Ropovík R, Peti D, Geľatko M. Laser Polishing of Vertically Oriented FDM-PLA Components: Influence of Laser Power and Polishing Speed on Surface Topography and Mechanical Response. Polymers. 2025;17(23):3096. doi:10.3390/polym17233096

BibTeX
@article{Stolrik2025,
  author = {Stolárik, Gabriel and Vandžura, Radoslav and Ropovík, Róbert and Peti, Damián and Geľatko, Matúš},
  title = {Laser Polishing of Vertically Oriented FDM-PLA Components: Influence of Laser Power and Polishing Speed on Surface Topography and Mechanical Response},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {23},
  pages = {3096},
  doi = {10.3390/polym17233096}
}
Kostenlos starten →