EUVIMEDEUVIMED entdecken
Crossref

Solid-State Upcycling of End-of-Life Al–Mn–Cu Alloy via Additive Friction Stir Deposition

Simone Amantia, R. Sarvesha, James Caudill, Livan Fratini, Fabrizio Micari, I. S. Jawahir

Journal of Manufacturing Science and Engineering · 01.10.2026 · 148 (10)

DOI: 10.1115/1.4071953 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing Science and Engineering, online erschienen am 30.06.2026. Verfasst von Simone Amantia und 5 weiteren Autor:innen. Die Arbeit nennt 24 Literaturangaben. Gefördert von: Ministero dell'Istruzione, dell'Università e della Ricerca.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The increasing emphasis on sustainable materials recovery has driven research efforts to explore solid-state upcycling routes as a low-energy alternative to remelting and casting, thereby enabling the circular economy. This study employed additive friction stir deposition (AFSD), a solid-state, friction-based additive manufacturing process in which solid feedstock rods are deposited layer by layer. In the present investigation, an end-of-life, nonheat-treatable aluminum alloy (Al–1.2Mn–0.2Cu, wt%) from end of use was mechanically shredded into chips and cold-compacted into square-section rods (∼11.7 mm × 11.7 mm) with a length of 151 mm. The relative density of compacted rods was ∼85%. The rods were subsequently deposited using AFSD with a zig-zag deposition strategy using a flat-faced tool. The mechanical properties of the deposits were evaluated through indentation and uniaxial tensile testing. The deposit exhibited an average Vickers hardness of 46.9 ± 3.5 HV0.1, a yield strength (YS) of 76 ± 15 MPa, an ultimate tensile strength of 162 ± 18 MPa, and an elongation to fracture of 12.6 ± 1.0%. Microstructural analysis revealed effective interlayer metallurgical bonding and significant grain refinement due to continuous dynamic recrystallization (cDRX), resulting in an average grain size of 4.4 ± 0.6 μm. No apparent porosity was observed in the build, indicating near-full densification. Overall, this study demonstrates a resource-efficient upcycling strategy for end-of-life aluminum waste via AFSD, aiming to minimize the energy demand associated with solid-state recycling routes and supporting the transition toward closed-loop circular manufacturing. A quantitative assessment of the energy consumption will be addressed in future studies.

Förderung

  • Ministero dell'Istruzione, dell'Università e della Ricerca

Zitieren

APA

Amantia, S., Sarvesha, R., Caudill, J., Fratini, L., Micari, F., & Jawahir, I. S. (2026). Solid-State Upcycling of End-of-Life Al–Mn–Cu Alloy via Additive Friction Stir Deposition. Journal of Manufacturing Science and Engineering, 148(10). https://doi.org/10.1115/1.4071953

Vancouver

Amantia S, Sarvesha R, Caudill J, Fratini L, Micari F, Jawahir IS. Solid-State Upcycling of End-of-Life Al–Mn–Cu Alloy via Additive Friction Stir Deposition. Journal of Manufacturing Science and Engineering. 2026;148(10). doi:10.1115/1.4071953

BibTeX
@article{Amantia2026,
  author = {Amantia, Simone and Sarvesha, R. and Caudill, James and Fratini, Livan and Micari, Fabrizio and Jawahir, I. S.},
  title = {Solid-State Upcycling of End-of-Life Al–Mn–Cu Alloy via Additive Friction Stir Deposition},
  journal = {Journal of Manufacturing Science and Engineering},
  year = {2026},
  volume = {148},
  number = {10},
  doi = {10.1115/1.4071953}
}
Kostenlos starten →