EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Corrosion Properties of Al-Cu-Mg Alloy Fabricated via Additive Friction Stir Deposition

Hu Wang, Zhixiong Zhu, Yongyong Lin, Dawei Guo iD, Guoshun Yang, Chen Wang iD, Jinbao Chen

Materials · 31.10.2026 · 19 (21) · 4630

DOI: 10.3390/ma19214630 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 31.10.2026. Verfasst von Hu Wang und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Astronautics, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key R&D Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Using as-received Al-Cu-Mg bars as the raw material, a 530 mm diameter Al-Cu-Mg alloy ring component was successfully fabricated via additive friction stir deposition (AFSD). Owing to the severe plastic deformation and dynamic recrystallization induced during the AFSD process, the microstructure was noticeably refined. The average grain size decreased from 35.84 μm to approximately 3.40 μm, with over 90% of grains below 4 μm. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests in 3.5 wt.% NaCl solution revealed that the AFSD-ed alloy exhibited a higher corrosion potential of −675.29 ± 7.78 mV (vs. Saturated Calomel Electrode, SCE) and a lower corrosion current density of 1.45 ± 0.04 × 10−6 A/cm2, compared with −684.33 ± 0.86 mV and 4.33 ± 1.30 × 10−6 A/cm2 for the as-received bar, respectively. EIS further confirmed superior corrosion resistance, as evidenced by larger capacitive arcs and a higher low-frequency impedance modulus. Microstructural characterization indicated that the corrosion mode, from propagating pits to isolated pits, is probably due to the refined grains and secondary phase particles during AFSD. These findings demonstrate that AFSD enables large, fully dense Al-Cu-Mg components with enhanced corrosion resistance, establishing AFSD as a promising route to improved corrosion performance for aerospace and defense applications.

Schlagwörter

Stichwörter der Autor:innen

Al-Cu-Mg alloyadditive friction stir depositioncorrosion performancemicrostructure

Autor:innen und Institutionen

  • School of Astronautics, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China.
  • Aerospace Engineering Equipment (Suzhou) Co. Ltd., Suzhou 215104, China.
  • Institute for Development & Quality, Macau, China.

ORCID-Profile: Dawei Guo, Chen Wang

Förderung

  • National Key R&D Program of China

Zitieren

APA

Wang, H., Zhu, Z., Lin, Y., Guo, D., Yang, G., Wang, C., & Chen, J. (2026). The Corrosion Properties of Al-Cu-Mg Alloy Fabricated via Additive Friction Stir Deposition. Materials, 19(21), 4630. https://doi.org/10.3390/ma19214630

Vancouver

Wang H, Zhu Z, Lin Y, Guo D, Yang G, Wang C, et al. The Corrosion Properties of Al-Cu-Mg Alloy Fabricated via Additive Friction Stir Deposition. Materials. 2026;19(21):4630. doi:10.3390/ma19214630

BibTeX
@article{Wang2026,
  author = {Wang, Hu and Zhu, Zhixiong and Lin, Yongyong and Guo, Dawei and Yang, Guoshun and Wang, Chen and Chen, Jinbao},
  title = {The Corrosion Properties of Al-Cu-Mg Alloy Fabricated via Additive Friction Stir Deposition},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {21},
  pages = {4630},
  doi = {10.3390/ma19214630}
}
Kostenlos starten →