Applying 3D ‐Printed Porous Ti6Al4V Prostheses to Repair Osteomyelitis‐Induced Partial Bone Defects of Lower Limbs: Finite Element Analysis and Clinical Outcomes
Orthopaedic Surgery · 2025-01 · 17 (1) · 115-124
DOI: 10.1111/os.14268 ↗Kurz gefasst
Fachartikel in der Zeitschrift Orthopaedic Surgery, online erschienen am 21.10.2024. Verfasst von Bingchuan Liu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopaedics, Peking University Third Hospital, Beijing, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Titanium, Osteomyelitis, Prosthesis Design. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Natural Science Foundation of China, Beijing Municipal Science and Technology Commission, Adminitrative Commission of Zhongguancun Science Park, Peking University Medicine Sailing Program for Young Scholars' Scientific & Technological Innovation.
Abstract (Originalsprache)
Objective
The clinical management of partial bone defects in lower limbs, particularly those resulting from osteomyelitis, remains a significant challenge. This study aimed to systematically evaluate the effectiveness of 3D‐printed porous Ti6Al4V prostheses in addressing osteomyelitis‐induced partial bone defects.
Methods
We established a comprehensive protocol for utilizing 3D‐printed prostheses for bone defect repair, encompassing 3D simulation of prosthesis implantation and internal fixation, finite element analysis (FEA), and clinical implementation. Mimics software facilitated simulation of fixation patterns and screw lengths. FEA modeled bone defects in the distal metaphyseal femur and distal diaphyseal tibia to assess changes in stress conduction pre‐ and post‐prosthesis implantation. The clinical study involved eight patients (average age: 56.3 years) with an average defect length of 14.9 cm. Postoperative outcomes were evaluated using X‐rays and the Lower Extremity Functional Scale (LEFS).
Results
FEA demonstrated that the implanted prostheses effectively shared stress and reduced the load on residual bone in both models, thus lowering the risk of fractures under external forces. The average follow‐up period was 24.5 months, with patients initiating weight‐bearing activities on average 7.8 days post‐surgery. Serial postoperative X‐rays demonstrated long‐term stability of the prostheses, with progressive bone regeneration around and integration with the prostheses. While two patients experienced infection recurrence requiring prosthesis removal and debridement, the remaining six showed significant improvement in LEFS scores, increasing from 31.5 preoperatively to 61.0 at the last follow‐up.
Conclusions
3D‐printed porous Ti6Al4V prostheses effectively restore anatomical integrity and optimize stress conduction in lower limbs, resulting in substantial functional recovery. This innovative approach shows promise for wider clinical adoption and warrants further investigation in medical practice.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Orthopaedics, Peking University Third Hospital, Beijing, China.
- Engineering Research Center of Bone and Joint Precision Medicine, Ministry of Education, Beijing, China.
- Beijing AKEC Medical Co., Ltd., Beijing, China.
ORCID-Profile: Yun Tian
Förderung
- National Natural Science Foundation of China
- Beijing Municipal Science and Technology Commission, Adminitrative Commission of Zhongguancun Science Park
- Peking University Medicine Sailing Program for Young Scholars' Scientific & Technological Innovation
- Key Clinical Projects of Peking University Third Hospital
Zitieren
APA
Liu, B., Tan, Q., Wang, Z., Hou, G., Wang, C., & Tian, Y. (2025). Applying 3D ‐Printed Porous Ti6Al4V Prostheses to Repair Osteomyelitis‐Induced Partial Bone Defects of Lower Limbs: Finite Element Analysis and Clinical Outcomes. Orthopaedic Surgery, 17(1), 115-124. https://doi.org/10.1111/os.14268
Vancouver
Liu B, Tan Q, Wang Z, Hou G, Wang C, Tian Y. Applying 3D ‐Printed Porous Ti6Al4V Prostheses to Repair Osteomyelitis‐Induced Partial Bone Defects of Lower Limbs: Finite Element Analysis and Clinical Outcomes. Orthopaedic Surgery. 2025;17(1):115-124. doi:10.1111/os.14268
BibTeX
@article{Liu2025,
author = {Liu, Bingchuan and Tan, Qizhao and Wang, Zhengguang and Hou, Guojin and Wang, Caimei and Tian, Yun},
title = {Applying 3D ‐Printed Porous Ti6Al4V Prostheses to Repair Osteomyelitis‐Induced Partial Bone Defects of Lower Limbs: Finite Element Analysis and Clinical Outcomes},
journal = {Orthopaedic Surgery},
year = {2025},
volume = {17},
number = {1},
pages = {115--124},
doi = {10.1111/os.14268}
}
EUVIMED