EUVIMEDDescoperă EUVIMED
Crossref

Effect of post‐printing curing time on cytotoxicity of direct printed aligners: A pilot study

Giorgio Iodice iD, Bjorn Ludwig iD, Elena Polishchuk iD, Raffaella Petruzzelli iD, Roberto Di Cunto iD, Soboh Husam iD, Mauro Farella iD

Orthodontics & Craniofacial Research · 2024

DOI: 10.1111/ocr.12819 ↗

At a glance

Journal article in Orthodontics & Craniofacial Research, 2024. Written by Giorgio Iodice and 6 co-authors. Institution: Department of Dental and Maxillo-Facial Sciences, Section of Orthodontics and Gnathology, University of Naples "Federico II", Naples, Italy. Major MEDLINE topics: Fibroblasts, Printing, Three-Dimensional, Cell Survival. Cited 40 times so far (Crossref); 31 references.

RezumatSubjectsDate bibliograficeCiteRelated studies

Abstract (original language)

Introduction

The aim of this in vitro study was to examine the potential impact of different curing times of 3D‐printed orthodontic aligners on their cytotoxicity.

Method

Some 60 samples of aligner material were directly 3D printed using Tera Harz TC‐85 DAC resin and randomly allocated to three different curing time groups (14, 24 and 50 min). Zendura FLX samples were used as control. The samples were incubated in saliva for 14 days, and then the supernatant was collected. Human gingival fibroblasts (HGF‐1)‐CRL2014 were used to evaluate potential cytotoxicity. Furthermore, HGF‐1 cells were plated on the samples as well as on a glass control sample. After 72 h of growth, their viability was tested.

Results

Compared with the glass, only the 50‐min curing time markedly reduced fibroblast cell growth. Additionally, a negative linear trend was observed between curing time and fibroblast growth. In comparison with the aligner control group, all samples, including the aligner control samples, exhibited a significant reduction in the viability of human fibroblasts when exposed to saliva.

Conclusions

3D directly printed aligners showed a cytotoxic effect similar to that of thermoformed conventional aligners in terms of fibroblasts growth. A linear trend was found between curing time and cells growth, indicating that directly printed aligners could exhibit higher cytotoxicity if exposed to a longer curing time. This dependence on curing time underscores the importance of following a strict manufacturing process.

Subjects

MeSH terms (MEDLINE)

FibroblastsPrinting, Three-DimensionalCell SurvivalHumansPilot ProjectsTime FactorsGingivaMaterials TestingCells, CulturedSalivaOrthodontic AppliancesCell Proliferation

Author keywords

3D printed alignersalignersbiocompatibilitycytotoxicityorthodontics

Authors and institutions

  • Department of Dental and Maxillo-Facial Sciences, Section of Orthodontics and Gnathology, University of Naples "Federico II", Naples, Italy.
  • Institute of Odontology, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden.
  • Telethon Institute of Genetics and Medicine (TIGEM), Pozzuoli, Italy.
  • University of Medicine and Pharmacy Grigore T. Popa, Bucharest, Romania.
  • Department of Oral Sciences, Faculty of Dentistry, Sir John Walsh Research Institute, University of Otago, Dunedin, New Zealand.
  • Department of Surgical Sciences, University of Cagliari, Cagliari, Italy.

ORCID profiles: Giorgio Iodice, Bjorn Ludwig, Elena Polishchuk, Raffaella Petruzzelli, Roberto Di Cunto, Soboh Husam, Mauro Farella

Cite

APA

Iodice, G., Ludwig, B., Polishchuk, E., Petruzzelli, R., Di Cunto, R., Husam, S., & Farella, M. (2024). Effect of post‐printing curing time on cytotoxicity of direct printed aligners: A pilot study. Orthodontics & Craniofacial Research. https://doi.org/10.1111/ocr.12819

Vancouver

Iodice G, Ludwig B, Polishchuk E, Petruzzelli R, Di Cunto R, Husam S, et al. Effect of post‐printing curing time on cytotoxicity of direct printed aligners: A pilot study. Orthodontics & Craniofacial Research. 2024. doi:10.1111/ocr.12819

BibTeX
@article{Iodice2024,
  author = {Iodice, Giorgio and Ludwig, Bjorn and Polishchuk, Elena and Petruzzelli, Raffaella and Di Cunto, Roberto and Husam, Soboh and Farella, Mauro},
  title = {Effect of post‐printing curing time on cytotoxicity of direct printed aligners: A pilot study},
  journal = {Orthodontics & Craniofacial Research},
  year = {2024},
  doi = {10.1111/ocr.12819}
}
Start for free →