EUVIMEDEUVIMED entdecken
Crossref

Effects of chemical and mechanical cleaning methods on the surface, physicochemical, and microbiological properties of extrinsically characterized 3D‐printed denture base resins after exposure to different pigmenting solutions

Ana Larisse Carneiro Pereira iD, Luiz Felipe Fernandes Gonçalves iD, Patrick Wesley Marques de Boa, Palloma Christine Queiroga Gomes da Costa iD, Matheus Harllen Gonçalves Veríssimo iD, Poliana Lima Bastos, Boniek Castillo Dutra Borges iD, Burak Yilmaz iD, André Ulisses Dantas Batista iD

Journal of Prosthodontics · 09.11.2026

DOI: 10.1111/jopr.70268 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 09.11.2026. Verfasst von Ana Larisse Carneiro Pereira und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dentistry, Universidade Federal de Juiz de Fora (UFJF-GV), Governador Valadares, Minas Gerais, Brazil. Die Arbeit nennt 45 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To investigate the effects of chemical and mechanical cleaning methods on the surface, physicochemical, optical, and microbiological properties of heat‐polymerized and extrinsically characterized 3D‐printed denture base resins after staining with different pigmenting solutions. Materials and Methods Square specimens (8.0 mm × 8.0 mm × 3.0 mm) were fabricated from two types of resins ( n = 160): an intrinsically characterized heat‐polymerized resin (HT‐STG) and an extrinsically characterized 3D‐printed resin (3D‐P). The specimens ( n = 40) were immersed in four staining solutions (coffee, tea, wine, and tobacco) for 7 days and then subjected to cleaning protocols for 14 days using chemical methods ( n = 10) (Corega Tabs, Efferdent, and BM4 NOVA Power 22%) or a mechanical method (Polident). Analyses were performed at three time points (baseline, staining, and cleaning) to evaluate surface roughness, Vickers hardness, water sorption and solubility, chemical composition, color, microbiological analysis, and scanning electron microscopy. Data were analyzed using four‐way ANOVA, three‐way ANOVA, and Tukey's post hoc test ( α = 0.05).

Results

Surface roughness, hardness, and color change were significantly influenced by interactions among resin type, cleaning protocol, staining solution, and evaluation time ( p < 0.05). HT‐STG showed greater color change, whereas 3D‐P exhibited greater surface changes. Whitening was most effective for color recovery, whereas Efferdent better preserved surface smoothness. Water sorption, solubility, and chemical composition remained stable, although biofilm formation varied among conditions.

Conclusions

Different combinations of tested resin type, cleaning protocol, stain type, and time play a role in maintaining surface roughness, hardness, color stability, and biofilm behavior.

Schlagwörter

Stichwörter der Autor:innen

3D printingcomplete dentureperoxidepigmentationstaining

Autor:innen und Institutionen

  • Department of Dentistry, Universidade Federal de Juiz de Fora (UFJF-GV), Governador Valadares, Minas Gerais, Brazil.
  • Program in Dentistry, Universidade Federal da Paraíba (UFPB), João Pessoa, Paraíba, Brazil.
  • Department of Restorative Dentistry, Universidade Federal da Paraíba (UFPB), João Pessoa, Paraíba, Brazil.
  • Department of Dentistry, Universidade Federal do Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil.
  • Department of Dentistry, Universidade Federal do Ceará (UFC), Sobral, Ceará, Brazil.
  • Department of Reconstructive Dentistry and Gerodontology, University of Bern, Bern, Switzerland.

ORCID-Profile: Ana Larisse Carneiro Pereira, Luiz Felipe Fernandes Gonçalves, Palloma Christine Queiroga Gomes da Costa, Matheus Harllen Gonçalves Veríssimo, Boniek Castillo Dutra Borges, Burak Yilmaz, André Ulisses Dantas Batista

Zitieren

APA

Pereira, A. L. C., Gonçalves, L. F. F., de Boa, P. W. M., da Costa, P. C. Q. G., Veríssimo, M. H. G., Bastos, P. L., Borges, B. C. D., Yilmaz, B., & Batista, A. U. D. (2026). Effects of chemical and mechanical cleaning methods on the surface, physicochemical, and microbiological properties of extrinsically characterized 3D‐printed denture base resins after exposure to different pigmenting solutions. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70268

Vancouver

Pereira ALC, Gonçalves LFF, de Boa PWM, da Costa PCQG, Veríssimo MHG, Bastos PL, et al. Effects of chemical and mechanical cleaning methods on the surface, physicochemical, and microbiological properties of extrinsically characterized 3D‐printed denture base resins after exposure to different pigmenting solutions. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70268

BibTeX
@article{Pereira2026,
  author = {Pereira, Ana Larisse Carneiro and Gonçalves, Luiz Felipe Fernandes and de Boa, Patrick Wesley Marques and da Costa, Palloma Christine Queiroga Gomes and Veríssimo, Matheus Harllen Gonçalves and Bastos, Poliana Lima and Borges, Boniek Castillo Dutra and Yilmaz, Burak and Batista, André Ulisses Dantas},
  title = {Effects of chemical and mechanical cleaning methods on the surface, physicochemical, and microbiological properties of extrinsically characterized 3D‐printed denture base resins after exposure to different pigmenting solutions},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70268}
}
Kostenlos starten →