EUVIMEDEUVIMED entdecken
Crossref

3D‐printed denture base resins: Glazing as an alternative to improve surface, mechanical, and microbiological properties

Ana Larisse Carneiro Pereira iD, João Pedro Dos Santos Silva, Manassés Tercio Vieira Grangeiro, Annie Karoline Bezerra de Medeiros, Marcos Antonio Bottino, Valentim A R Barão, Adriana da Fonte Porto Carreiro

Journal of Prosthodontics · 16.12.2024

DOI: 10.1111/jopr.14001 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 16.12.2024. Verfasst von Ana Larisse Carneiro Pereira und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 47 Literaturangaben. Gefördert von: Coordination for the Improvement of Higher Education Personnel (CAPES), Brazil [Finance code 001], The commercial companies: Makertech Labs, Yller Biomaterials and PrintaX.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the impact of glazing denture base resins (heat‐polymerized and 3D‐printed) on surface, mechanical, and microbiological properties. Materials and Methods Discs (10 × 3 mm) and bars (64 × 10 × 3.3 ± 0.2 mm) were manufactured using heat‐polymerized denture base resin (CT) and 3D‐printed denture base resin (Yller [YL], Prizma [PZ] and PrintaX [PX]). These were divided into two groups: unglazed and glazed. Surface roughness (Ra), wettability (contact angle), brightness (GU), and topography (via scanning electron microscopy) were assessed, along with microbiological analysis of dual‐species biofilms (Streptococcus mitis and Candida albicans ) and Knoop microhardness on discs ( n = 10). Flexural strength testing was conducted separately on bars ( n = 20). Half of the specimens subjected to surface and mechanical characterizations were thermocycled (10,000 cycles). Mann–Whitney test ( p < 0.05) and simple and multiple linear regression analysis ( p < 0.20) were employed to evaluate the impact of glazing on denture base resins.

Results

The application of glaze reduced roughness by 0.33 µm and water contact angle by 8.47º, while increasing brightness by 21.30 units ( p < 0.001) for 3D‐printed resins compared to CT. After thermal cycling, roughness and wettability increased, while brightness decreased ( p < 0.05). The glaze also increased hardness, with no adverse effects from thermal cycling ( p < 0.001), and enhanced flexural strength for PZ compared to CT ( p < 0.001). Additionally, C. albicans colonization decreased by 7.79 log CFU/mL in mixed biofilms for 3D‐printed resins compared to CT ( p < 0.05).

Conclusions

The application of glaze resulted in smoother, brighter, and harder surfaces for the 3D‐printed resins, while also reducing biofilm colonization.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingcomplete denturedigital dentureglazing

Autor:innen und Institutionen

  • Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil.
  • Department of Prosthodontics and Periodontology, Piracicaba Dental School, Universidade Estadual de Campinas (UNICAMP), Piracicaba, São Paulo, Brazil.
  • Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), São Paulo, Brazil.
  • Department of Biomaterials, Dental Materials, and Prosthodontics, Institute of Science and Technology, São Paulo State University (UNESP), São José dos Campos, Brazil.

ORCID-Profile: Ana Larisse Carneiro Pereira

Förderung

  • Coordination for the Improvement of Higher Education Personnel (CAPES)
  • Brazil [Finance code 001]
  • The commercial companies: Makertech Labs, Yller Biomaterials and PrintaX

Zitieren

APA

Carneiro Pereira, A. L., Dos Santos Silva, J. P., Grangeiro, M. T. V., de Medeiros, A. K. B., Bottino, M. A., Barão, V. A. R., & da Fonte Porto Carreiro, A. (2024). 3D‐printed denture base resins: Glazing as an alternative to improve surface, mechanical, and microbiological properties. Journal of Prosthodontics. https://doi.org/10.1111/jopr.14001

Vancouver

Carneiro Pereira AL, Dos Santos Silva JP, Grangeiro MTV, de Medeiros AKB, Bottino MA, Barão VAR, et al. 3D‐printed denture base resins: Glazing as an alternative to improve surface, mechanical, and microbiological properties. Journal of Prosthodontics. 2024. doi:10.1111/jopr.14001

BibTeX
@article{CarneiroPereira2024,
  author = {Carneiro Pereira, Ana Larisse and Dos Santos Silva, João Pedro and Grangeiro, Manassés Tercio Vieira and de Medeiros, Annie Karoline Bezerra and Bottino, Marcos Antonio and Barão, Valentim A R and da Fonte Porto Carreiro, Adriana},
  title = {3D‐printed denture base resins: Glazing as an alternative to improve surface, mechanical, and microbiological properties},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.14001}
}
Kostenlos starten →